 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Kenyon Spars D-Section Boom |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Kenyon Spars D-Section Boom |
|
|
|
|
| Kenyon Spars D-Section Boom Measurements (outside): 3.75" x 2.25" (95mm x 57mm) Wall Thickness: .100" Weight/ft.: 1.3 lbs. Moments of inertia: Ixx = 1.5", Iyy = .63" Circumference: 9 5/8" Sail slides: 1/2" round slugs (A018, A118) or 1/2" boltrope Alloy: 6063-T6 Standard Boom Lengths: 7'6", 8'5", 9'6 1/2", 11'3", 12'8", 15' Common Boom usage: Atlantic; Bayliner BU 200/210, 240/245, 270/285; Boston Whaler Harpoon 6.2*; Cal 25; 2-25; Capri 25; DM 22; Ericson 21.8, 25+; Evelyn 26OD, 32*; Impulse 26; International 210; |
|
| Hunter 25, 25.5, 27*; Grampian 26, 30;
J/24; Lancer 25,
28, 29; Merit 22, 25; Monterey 24; NA 23K; O'Day 22*, 23, 25, 26, 27*, 32K Mizzen; Pearson
Triton 21, 22, 23, 25, 27; Rainbow 24; San Juan 24, 26; Sea Sprite 23; Seidelman 24; S2 6.7, 6.9;
Sonar; Texas T-26;
Thunderbird 25; US 21, 22, 25, 27; and hundreds of other models in the 21' - 28' range.
See Also: Kenyon Spars D-Section Mast |
|
|
|
|
|
Kenyon D-Section Boom Tube
Kenyon D-Section Boom Hardware - D-Section Standard Boom Ends |
|
|
|
Kenyon D-Section Boom Tube
D-Section Boom Tube - Clear Anodized: K-DCA-___: |
|
|
|
Kenyon D-Section Boom Assemblies If you require a complete Boom Assembly, select from components below and contact us with specifications. Standard and Roller Reefing Boom Kits are listed below. |
|
|
|
Kenyon D-Section Boom Kits Kenyon D-Section Booms are available in Kit form. Kits include all hardware, fasteners, instructions, and finished, machined tube. Tools required include a drill, 10-24 and 1/4-20 taps, common screw drivers and wrenches, and a basic understanding of measuring, drilling and tapping. For most Booms drilling holes, and tapping some of them, are all the machining that is required to complete assembly. For Internal Line Booms, an 1/8" Nicopress Tool is also required to finish the Outhaul wire. This is the least expensive and most expedient way to get a new Boom.
|
|
D-Section Boom Kit - Standard: K-DBK-1S: Kenyon D-Section Standard Boom Kit comes complete with all hardware required to assemble a D-Section Standard Boom, except the Boom Tube. Kit includes: Gooseneck with Toggle (but without Slide or Mast Bracket), K-2123; Outhaul casting, K-D444; (1) Boom Bail, K-10456; (1) 4" Cleat for Outhaul line, D-10324; all the fasteners required, and instructions. Order D-Section Boom Tube separately (specify finish and length), if additional parts (Gooseneck Slide, vang bail, etc.) are required, they must be ordered separately. All components are detailed below. Tools required include a drill, 10-24 and 1/4-20 taps, common screw drivers and wrenches, and a basic understanding of measuring, drilling and tapping.
|
|
D-Section Boom Kit - Roller Reefing: K-DBK-1RR: Kenyon D-Section Roller Reefing Boom Kit comes complete with all hardware required to assemble a D-Section Roller Reefing Boom, except the Boom Tube. Kit includes: Roller Reefing Gooseneck with Toggle (but without Slide or Mast Bracket), K-2123RR; Outhaul Assembly with 2 Tangs, K-D444-2; 4" Cleat for Outhaul line, D-10324; all the fasteners required, and instructions. Order D-Section Boom Tube separately (specify finish and length), if additional parts (Gooseneck Slide, vang bail, etc.) are required, they must be ordered separately. All components are detailed below. Tools required include a drill, 10-24 and 1/4-20 taps, common screw drivers, and a basic understanding of measuring, drilling and tapping.
|
|
D-Section Boom Kit - Internal Outhaul & Reef Lines: K-DBK-2: Kenyon D-Section Internal Boom Kit comes complete with all hardware required to assemble a D-Section Internal Boom with a 4-1 outhaul and 2 Internal Reef Lines, except the Boom Tube. Kit includes: Gooseneck with sheaves and cams (without Toggle), K-43022; Outhaul Assembly with 3 sheaves, K-43023; (1) Boom Bail, K-10456; 4-1 Outhaul Tackle with Clew Shackle, K-90225M; 4" Cleat for Outhaul line, D-10324; all the fasteners required, and instructions. Order D-Section Boom Tube separately (specify finish and length), if additional parts (Toggle, bails, etc.) are required, they must be ordered separately. All components are detailed below. Tools required include a drill, 10-24 and 1/4-20 taps, common screw drivers and wrenches, and a basic understanding of measuring, drilling and tapping. An 1/8" Nicopress Tool is also required to finish the Outhaul wire. |
|
Kenyon D-Section Boom Hardware Listed below are parts specific to the Kenyon D-Section Boom Section. For more generic parts, see Kenyon Exit Plates and other categories listed under Kenyon Spar Parts. There are many parts for specific configurations that are not listed here. If you require D-Section Boom Components not listed here please contact us with details. All Aluminum Castings listed below are carefully hand finished and coated with a baked-on Black Epoxy (to retard corrosion) as Standard. Castings are available Clear Anodized at additional cost, add CA to part number. D-Section Internal Reefing Boom Ends |
||||
|
|
||||
| D-Section Standard Boom Ends | ||||
| D-Section Standard Gooseneck Assemblies & Parts | ||||
|
D-Section Gooseneck Ass'y w/ 1/2" Slide: K-10553: Cast aluminum boom end fitting includes captive SS tack pin and SS yoke, K-80, 1" SS Toggle, K-1993, and 1/2" SS Gooseneck Slide, K-1685A. Fits B, D, E, 3049, 3650 and all mast sections using 1/2" round slugs or boltrope. Parts for D-Section Standard Gooseneck Assemblies.
|
|
|||
|
|
D-Section Gooseneck Ass'y w/ Yoke & Toggle: K-2123: As K-10553 (above), but without SS Gooseneck Slide. Toggle attaches directly to any of the Kenyon gooseneck brackets designed for a 1" Toggle (see individual mast sections), and Kenyon gooseneck slides designed for a 1" Toggle (below). Parts for D-Section Standard Gooseneck Assemblies.
|
|
||
|
|
D-Section Gooseneck Ass'y w/ Yoke: K-2123NT: As K-2123 (above), but without SS Gooseneck Toggle. Yoke attaches to a variety of Gooseneck Toggles up to 1" wide, but is normally used with Kenyon 1" SS Toggle, K-1993. Parts for D-Section Standard Gooseneck Assemblies.
|
|
||
| D-Section Roller-Reefing Gooseneck Ass'y w/ 1/2" Slide: K-10553RR: | ||||
| Spring-loaded roller-reefing mechanism works by
pulling aft on the boom and turning it in 1/4 turn increments. SS yoke assembly is fixed
in a square recess until boom is pulled aft. SS Spring locks yoke into recess when boom is
released. Works only with end-boom sheeting systems with swiveling mainsheet and topping
lift attachments. Cast aluminum boom end fitting includes captive SS tack pin and SS
roller-reefing yoke assembly, K-8890A, with 1" SS Toggle, K-1993,
and 1/2" SS Boltrope Slide, K-1685A. Fits B, D, E, 3049, 3650 and all mast sections
using 1/2" round slugs or boltrope.
Parts for D-Section Roller-Reefing Gooseneck Assemblies.
|
|
|||
| D-Section Roller-Reefing Gooseneck Ass'y w/ Toggle: K-2123RR: | ||||
|
|
As K-10553RR (above), but
without SS Gooseneck slide. Toggle attaches directly to any of the Kenyon gooseneck
brackets designed for a 1" Toggle (see individual mast sections), and Kenyon
gooseneck slides designed for a 1" Toggle (below). Parts for
D-Section Roller-Reefing Gooseneck Assemblies.
|
|
||
|
|
D-Section Roller-Reefing Gooseneck Ass'y: K-2123RRNT: As K-2123RR (above), but without SS Gooseneck Toggle. Yoke attaches to a variety of Gooseneck Toggles up to 1" wide, but is normally used with Kenyon 1" SS Toggle, K-1993. Parts for D-Section Roller-Reefing Gooseneck Assemblies.
|
|
||
|
SS Gooseneck Slide - 1" for Large Boltrope: K-1685A: SS Gooseneck Slide fits any gooseneck assembly using the standard 1" Toggle, K-1993, with a 1/4" bolt and locknut (included). Slide has heavy welded SS ring for downhaul attachment. Slide is 3" long x 1" wide (maximum). Fits B, D, E, 3049, 3650 and all mast sections using 1/2" round slugs or boltrope.
|
|
|||
|
SS Gooseneck Slide - 1" for Small Boltrope: K-10331A: SS Gooseneck Slide fits any gooseneck assembly using the standard 1" Toggle, K-1993, with a 1/4" bolt and locknut (included). Slide has heavy welded SS ring for downhaul attachment. Slide is 2 1/2" long x 1" wide (maximum). Fits A, C-1, C-6, 2331, MORC and other mast sections that can accommodate only 3/8" round slugs or boltrope.
|
|
|||
|
SS Gooseneck Slide - 1" for 7/8" Flat Track: K-1686A: SS Gooseneck Slide fits any gooseneck assembly using the standard 1" Toggle, K-1993, with a 1/4" bolt and locknut (included). Slide has heavy welded SS ring for downhaul attachment. Slide is 3" long x 1 1/16" wide (maximum). Fits on a SS 7/8" x 1/8" Flat External Track.
|
|
|||
| Gooseneck Slide & Toggle Ass'y for 3/4" Internal Flat Track: K-PP-M6ATS: | ||||
|
Aluminum Gooseneck Slide with 1 1/2" Toggle to fit D-Section Gooseneck Assemblies with Tack and
Yoke,
K-2123NT, and K-2123RRNT (above). Slide fits integral Track in Kenyon
3550, 3756, Rig-Rite, Pearson, MetalMast and most other Mast Sections with a 3/4" Internal Flat
Track.
Gooseneck Slide is 4" long and features 5/16" hole for downhaul line or shackle.
Cast Toggle, PP B4C, is 3/4" wide and has 1/4" horizontal Pin hole.
Includes nylon spacer washers and SS bolt w/ locknut to attach to standard 1" SS
Yokes, K-80, and K-8890.
|
||||
|
|
||||
| D-Section Standard Outhaul Assemblies & Parts | ||||
|
D-Section Outhaul Casting: K-D444: Heavy-duty Black Epoxy coated cast aluminum Outhaul End has tab with 2 holes for outhaul, and/or topping lift attachment.
|
|
|||
|
D-Section Outhaul
Ass'y w/ Tang: K-D444-1: Cast aluminum boom end fitting has tab with 2 holes for outhaul, and/or topping lift attachment. Includes swiveling tang for mainsheet or topping lift attachment. Swiveling attachments for mainsheet and topping lift are required for use with roller-reefing goosenecks.
|
|
|||
|
D-Section Outhaul
Ass'y w/ 2 Tangs: K-D444-2: Cast aluminum boom end fitting has tab with 2 holes for outhaul, and/or topping lift attachment. Includes 2 swiveling tangs for mainsheet and/or topping lift attachment. Swiveling attachments for mainsheet and topping lift are required for use with roller-reefing goosenecks.
|
||||
|
|
Mainsheet Tang for D-Section Boom: K-360: Flat Mainsheet Tang attaches to Boom end casting using a 3/8" bolt. For use with Spartan CD-2, Kenyon D-Section, and similar sized booms. Mainsheet Tang is 5" long x 1" wide x .076" thick with (1) 3/8" mounting hole and a 1/2" x 1" slot for attachment of Mainsheet block.
|
|||
|
|
||||
| D-Section Internal Reefing Boom Ends | ||||
D-Section Internal Gooseneck Assemblies Kenyon Internal Gooseneck Assemblies allow easy control of up to three internal lines. An outhaul on the bottom centerline which is led to a cleat on the underside of the boom, and one or two reef lines which can be cleated with integral friction-lock lever-action cams, or led to the deck and cleated aft. |
||||
| Note: Kenyon Internal Gooseneck
Assemblies are now equipped with the new friction-lock lever-action cams for greater
holding ability, and SS cover plates to keep the reef lines captive at all times. Old-Style
units featured Spring Cams (with or w/o handles), and different reef sheaves than
the improved version. The Old-Style units are easily identified by the absence of
the SS cover plates. While upgrading to the improved style using one of the
K-11442
Conversion Kits (below) is recommended, original parts for the Old-Style gooseneck are
still available. See Parts for D-Section Old-Style
Internal Gooseneck.
|
||||
| D-Section Internal Gooseneck Ass'y w/ Toggle/Tack fitting: K-43022A: | ||||
| Cast aluminum gooseneck assembly incorporates
provisions for internal outhaul and 2 internal reef lines. Outhaul line exits through
aluminum sheave, K-198-4A, on centerline and runs along boom
bottom to a cleat. Reef lines exit port and starboard running past lever action cams, over
Delrin sheaves, and down. SS cover plates keep lines on sheaves at all times. Includes SS
combination Toggle/Tack/Reef Hook Assembly K-10518A. Toggle
attaches to any Kenyon gooseneck bracket designed for 1 1/2" Toggle and 1/4"
vertical pin. Vertical pin, K-CP4-61, is not included. Distance
from vertical Toggle Pin to boom tube is 5". Parts
for New-Style D-Section Internal Gooseneck Assemblies.
|
|
|||
|
D-Section Internal Gooseneck Ass'y: K-43022: As D-43022A, above, but without SS combination Toggle/Tack/Reef Hook Assembly, K-10518A. Attaches to K-10518A or other Toggles up to 11/16" wide, using a 3/8" bolt and locknut (included). Casting extends 4 1/2" (maximum) forward of the boom tube. Distance from horizontal Pin hole to boom tube is 4". Parts for New-Style D-Section Internal Gooseneck Assemblies.
|
|
|||
|
D-Section Internal Gooseneck Ass'y w/ Port Cam: K-43022P: D-Section Internal Gooseneck Ass'y w/ Starboard Cam: K-43022S: As K-43022, above, but with single reef cam, sheave and cover plate. Specify Port or Starboard Cam. Parts for New-Style D-Section Internal Gooseneck Assemblies.
|
|
|||
|
D-Section Internal Gooseneck Ass'y w/o Cams: K-43022NC: As K-43022, above, but with SS spacers in place of the reef cams. For use where reef lines are led down to the deck and cleated aft on the cabin top. Parts for New-Style D-Section Internal Gooseneck Assemblies.
|
||||
|
D-Section Internal Gooseneck Ass'y for Outhaul: K-11103A: As K-43022, above, but with outhaul sheave only, and no provisions for reef lines. Parts for New-Style D-Section Internal Gooseneck Assemblies.
|
||||
|
D-Section Gooseneck Ass'y for Jib Club: K-11103: As K-11103A, above, but with no sheaves - for staysail booms, jib clubs, and other booms with no internal lines. Commonly used with club pedestals and loose-footed jibs where the tack is secured by means of a pennant attached to the base of the stay. Casting extends 4 1/2" (maximum) forward of the boom tube.
|
||||
|
|
||||
|
Double Reef Cam Kit for D-Section Gooseneck: K-11442: Cam Conversion Kit for D-Section Gooseneck converts Old-Style Spring-Cam arrangement to the New-Style friction cam assembly. Easily installed Kit includes everything necessary for 2 reef lines including Cam levers, adjustable friction washers, reef sheaves, SS spacers, Cover plates, bolts and locknuts. Individual components are listed separately, See Parts for New-Style D-Section Internal Gooseneck Assemblies. The only machining required is to drill the old-style 1/4" sheave axle (forward) hole to 5/16".
|
|
|||
|
Port Reef Cam Kit for D-Section Gooseneck: K-11442P: Starboard Reef Cam Kit for D-Section Gooseneck: K-11442S: Single Cam Conversion Kit for D-Section Gooseneck converts Old-Style Spring-Cam arrangement to the New-Style friction cam assembly. Easily installed Kit includes everything necessary for single reef line including Cam lever, adjustable friction washers, reef sheave, SS spacer, Cover plate, bolts and locknuts. Individual components are listed separately, See Parts for New-Style D-Section Internal Gooseneck Assemblies. The only machining required is to drill the old-style 1/4" sheave axle (forward) hole to 5/16". Specify Port or Starboard.
|
||||
|
Sheave Only Conversion Kit for D-Section Gooseneck: K-11442NC: Sheave Conversion Kit for D-Section Gooseneck converts Old-Style Gooseneck to the New-Style with Cover Plates, Sheaves, and No cams. Easily installed Kit includes everything necessary for leading reef lines down and aft, including (2) reef sheaves, (4) SS spacers, Port and Starboard Cover plates, bolts and locknuts. Individual components are listed separately, See Parts for New-Style D-Section Internal Gooseneck Assemblies. As K-11442, above, but with 2 SS Spacers to replace the reef cams. The only machining required is to drill the old-style 1/4" sheave axle (forward) hole to 5/16".
|
||||
|
|
||||
|
Gooseneck Toggle/Tack Ass'y w/ Reef Hooks: K-10518A: Used with the K-10554 gooseneck bracket, and Kenyon 2333 or "D" section boom, this combination Toggle/Tack/Reef Hook Assembly features 3 tack positions and includes 3/8" tack fastpin, K-10399. Takes 1/4" vertical pin and 3/8" horizontal pin. Two 1/4" reef hooks allow for ease of reefing from either side of the boom. Toggle portion is 1 1/2" high x 11/16" wide with 1" between pin centers. Unit (excluding Reef Hooks) is 4" high x 11/16" wide x 2 1/4" long.
|
|
|||
|
Gooseneck Toggle/Tack Ass'y: K-10518N: As K-10518A, above, but without reef hooks. This combination Toggle and Tack Assembly features 3 tack positions and includes 3/8" tack fastpin K-10399. Takes 1/4" vertical pin and 3/8" horizontal pin. Toggle portion is 1 1/2" high x 11/16" wide with 1" between pin centers. Unit is (maximum) 4" high x 11/16" wide x 2 1/4" long.
|
|
|||
|
Gooseneck Toggle/Tack Ass'y: K-10518E: As K-10518N, above, but modified to increase the Tack Setback by 1". Toggle portion is 1 1/2" high x 11/16" wide with 1" between pin centers. Takes 1/4" vertical pin and 3/8" horizontal pin. Toggle fits all Kenyon Mast Brackets and a variety of Gooseneck Slides designed for a 1 1/2" Toggle with a 1/4" vertical pin. Toggle portion is 1 1/2" high x 11/16" wide with 2" between pin centers. Unit is (maximum) 4" high x 11/16" wide x 2 7/8" long, and includes 3/8" tack fastpin K-10399. Specially for use with Gooseneck Slide for 3/4" Internal Flat Track, PP-M6A, and as used on the Freedom 25.
|
|
|||
|
Tack Fastpin for 1 1/2" Toggle/Tack Ass'y: K-10399 (FP-6-28): SS Fastpin is 3/8" diameter x 7/8" long. Used in all K-10518 1 1/2" Toggle/Tack/Reef Hook Assemblies.
|
||||
|
SS Gooseneck Toggle - 1 1/2" High: K-10518C: Solid cast SS Gooseneck Toggle is 1 1/2" high and accommodates 1/4" vertical pin and 3/8" horizontal pin. SS Toggle is 1 1/2" high x 1/2" wide x 2 1/4" (maximum) long, pin holes are on 1" centers. Toggle fits a variety of Mast Brackets and Gooseneck Slides designed for a 1 1/2" Toggle with a 1/4" vertical pin.
|
||||
| Vertical Gooseneck Pin for 1 1/2" Toggle & SS Bracket: K-CP4-61: | ||||
| Clevis pin is 1/4" diameter x 1 7/8" long. Used to
attach the K-10518 Toggle/Tack/Reef Hook Assemblies to the Gooseneck Bracket on the
mast.
|
||||
| Vertical Gooseneck Pin for 1 1/2" Toggle & Aluminum Bracket: K-CP4-76: | ||||
| Clevis pin is 1/4" diameter x 2 3/8" long, for use with New-Style
K-43024AP Aluminum weld-on Gooseneck Bracket and K-10518 1 1/2"
Gooseneck Toggles. As used on newer J/24's.
|
||||
|
|
||||
| D-Section Internal Outhaul Assembly | ||||
|
D-Section Internal Outhaul Ass'y: K-43023: Cast aluminum boom end fitting has centerline aluminum sheave for 1/8" wire or up to 3/16" line, and (2) 1 7/8" nylon sheaves for up to 3/8" reef lines. Includes 1/4" clevis pin for topping lift attachment. Casting extends 2 1/4" (maximum) aft of the boom tube. Parts for K-43023 D-Section Internal Outhaul Assembly.
|
|
|||
|
D-Section Internal Outhaul Tackle, 4-1: K-90225M: Internal Outhaul Tackle for use with D Section Boom provides a 4-1 purchase. Block and Tackle assembly includes 17' of 1/4" line and 12' of 1/8" wire spliced to the Blocks. Becket block attaches to bolt at forward end of boom, line exits through centerline Gooseneck sheave, wire exits through centerline sheave in outhaul assembly. Wire length is suitable for longest standard length boom, but must be cut shorter in most applications. Includes fiddle block, single block w/ becket, spliced line, wire, and loose captive-pin Clew shackle w/ thimble & nicopress. An 1/8" Nicopress Tool is required for installation. 02 L30
|
||||
|
|
||||
| D-Section Boom Accessories | ||||
| Outhaul Slides A variety of Outhaul Slides are available to fit the 1/2" Boltrope groove in the D-Section Boom. See Outhaul Slides for 1/2" Boltrope Groove.
|
||||
|
Boom Bail - 1/4" x 2 1/4" wide: K-10456: Heavy SS Boom Bail made from 1/4" rod is designed to be attached with (1) 1/4" SS bolt and nut. Formed at 2 1/4" wide, width can be varied to fit larger or smaller sections. Bail length, from bolt center, is 2 1/2". For use with D-Section boom.
|
|
|||
|
Boom Bail Bolt Ass'y - 1/4" for D-Section Boom: K-10456BA: Boom Bail bolt assembly includes 1/4" SS bolt x 2 3/4", with locknut, and nylon washers to prevent bail from damaging boom surface as it pivots. |
|
|||
|
Boom Bail - 3/8" x 2 1/4" wide: K-10456H: Heavy SS Boom Bail made from 3/8" rod is designed to be attached with (1) 3/8" SS bolt and nut. Formed at 2 1/4" wide, width can be varied to fit larger or smaller sections. Bail length, from bolt center, is 3 1/2". For use with D-Section boom.
|
||||
|
Boom Bail Bolt Ass'y - 3/8" for D-Section Boom: K-S9010BA: Boom Bail bolt assembly includes 3/8" SS bolt x 3", with locknut, and nylon washers to prevent bail from damaging boom surface as it pivots.
|
||||
|
Boom Bail - Internal: K-11364: Internally mounted bail has a 1/4" SS bail welded to a plate formed to fit the inside of the boom. Unit is mounted inside the boom, where bail protrudes through a 1" x 1/4" slot, and is held in place with (2) 3/16" SS rivets on 1 7/8" centers. Curved plate measures 2 1/4" long x 3/4" wide. For use with 2632, D and similar Boom Sections. As used on Sonar.
|
|
|||
|
Vang Bracket for D-Section Boom: K-1757: SS Vang Bracket is contoured to fit D-Section boom and has welded triangle with 1/2" hole for attachment of vang tackle. Unit is 2 1/2" long, and fastens with (6) 3/16" (#10) fasteners.
|
|
|||
|
Weld-in Boom Vang Lug w/ 5/8" hole: K-11700J: Heavy-duty Aluminum Boom Vang Attachment Lug is welded into the Boom. Vang Lug slides into Boom, drops through a 3/8" wide x 3" long slot, and is welded in place from the outside. Lug is longer than slot it fits in to provide stiffening and reinforcement in this high-stress area. Vang Lug is cut from 6061-T6 Plate and is (maximum) 4" long x 3/8" wide x 1 3/4" high, Lug projects approximately 1 3/8" from underside of Boom when installed. Vang Lug has 5/8" hole for use with any shackle. As used on J/24 Racing Boom.
|
|
|||
|
Boom Vang Ball Attachment Plate for D-Section Boom: K-2182: Formed SS plate for attachment of Boom Vang with 1/8" wire swage ball. Allows for quick attachment and removal of Boom Vang, raised channel design allows easy installation without milling slot in boom. Channel projects approximately 3/8" from underside of Boom when installed. Formed Stainless Steel plate is 2" long x 1 7/8" high. Fastens with (6) 3/16" (#10) screws or rivets.
|
||||
|
Boom Vang Ball Attachment Plate for Flush Mounting: K-2182F: Formed SS plate for attachment of Boom Vang with 1/8" wire swage ball. Allows for quick attachment and removal of Boom Vang, flush mounting design allows use with Roller-Reefing booms. Base is curved to fit a variety of Boom Sections, narrow profile allows it to be bent to fit others. Formed Stainless Steel plate is 3" long x 1 1/2" wide. Mounting requires 3/8" wide x 1 1/4" long slot in Boom. Fastens with (6) 3/16" (#10) screws or rivets.
|
|
|||
|
Boom Vang Wire Pennant w/ Swage Ball: K-2182WP: Wire Pennant for attachment of Boom Vang to Boom Vang Ball Attachment Plate. Pennant is 1/8" wire with swage ball and shank (MS20664-4) on one end and a nicopress and thimble on the other. Thimble allows attachment of any upper Vang block. Assembly is 6" long. Ball is suitable for all Ball Attachment Plates with a slot that is 1/4" wide or less.
|
|
|||
|
|
||||
|
Spar Cleat - 4" long: Ken D-10324: Cast Aluminum Spar Cleat is a low-profile design with a narrow base suitable for use with line up to 3/8" diameter. Commonly used for Outhaul Line. Black Epoxy coated Cleat is 4" long, and fastens to spar with (2) 3/16" (#10) FH screws on 1 3/16" centers. See also, other Kenyon Spar Cleats.
|
||||
|
Clam Cleat w/ Fairlead & Curved Base: K-9115X: Clam Cleat with fairlead is used in place of standard Spar Cleat for frequent Outhaul adjustment in racing applications. Best mounted forward of an eyestrap (K-226) with small block (Har 082, or equivalent). Suitable for use with 1/8"-1/4" (3-6mm) line, black plastic unit fastens with (2) #8 x 3/4" FH Screws on 2 5/8" (66mm) centers. Unit measures 3 1/4" long x 11/16" wide (82x18mm). CL203 CC Jr.
|
||||
|
SS Eyestrap: K-226: Small Stainless Steel Eyestrap is used for securing smaller items to boom. Attaches to Boom with (2) 3/16" (#10, 5mm) screws or rivets.
|
||||
|
Single Bullet Block: Har 082: Small single Bullet Block is used for the Outhaul line on the bottom of the Boom. Plastic Ball-Bearing Block has 1 1/8" OD Delrin Sheave suitable for use with line up to 5/16" diameter. Use with K-226 Eyestrap and K-9115X Clam Cleat, above.
|
||||
|
Cheek Block w/ Curved Base: K-140X: Cheek Block with curved base is used on smaller Kenyon Booms for Outhaul and Reef lines. SS Cheek Block has 1 1/16" OD Delrin Sheave suitable for use with line up to 3/8" diameter. Base is 3 3/16" long x 7/8" wide, and fastens to spar with (4) 3/16" (#10) RH screws on 2 11/16" (horizontal) and 1/2" (vertical) centers. |
|
|||
