 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
D-Section Old-Style Internal Gooseneck Parts |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
D-Section Old-Style Internal Gooseneck Parts |
|
|
|
|
| Note: Kenyon Internal Gooseneck Assemblies are now equipped with the new friction-lock lever-action cams for greater holding ability, and SS cover plates to keep the reef lines captive at all times. Old-Style units featured Spring Cams (with or w/o handles), and different reef sheaves than the improved version. The Old-Style units are easily identified by the absence of the SS cover plates. While upgrading to the improved style using one of the K-11442 Conversion Kits (below) is recommended, original parts for the Old-Style gooseneck are still available, below. | |
|
|
|
|
D-Section Internal Gooseneck Casting - Old Style: K-10463X: Replacement casting is as K-10463, but has holes drilled for use with Old-Style Spring-Cam assemblies and sheaves listed below. Casting extends 4 1/2" (maximum) forward of the boom tube. Distance from horizontal Pin hole to boom tube is 4".
|
|
| Reefing Sheave for Old Style D-Section Gooseneck:
K-198-3.5A: Anodized aluminum sheave is 7/8" OD x 31/64" wide x 1/4" ID (2 required).
|
|
| Reefing Sheave Axle for Old Style D-Section Gooseneck: K-10477: | |
| SS axle pin is 1/4" diameter x 1 15/16" grip, with a turned groove on each
end to
accept 1/4" SS Snap Rings, K-63016 (2 included).
|
|
| SS Snap Rings for 1/4" Axle Pin: K-63016-2P: In 2-pack. Require small snap ring pliers for attachment.
|
|
| Reef Cam Assembly for Old Style Gooseneck - Port: K-GNCA-P: Reef Cam Assembly for Old Style Gooseneck - Starboard: K-GNCA-S: |
|
| Extruded aluminum Spring-Cam assembly fits on 3/8" pin
and includes Cam, SS spring, and molded nylon insert.
|
|
|
Reef Cam Assembly w/ handle for Old Style Gooseneck - Port: K-GNCAH-P: Reef Cam Assembly w/ handle for Old Style Gooseneck - Starboard: K-GNCAH-S: |
|
| Extruded aluminum Spring-Cam assembly with handle fits on
3/8" pin and includes Cam, SS spring, and molded nylon insert. As K-GNCA-P, and S
(above), but cam incorporates a SS handle. Specify Port or Starboard.
|
|
| Reefing Cam Axle for Old Style D-Section Gooseneck:
K-10378: SS axle pin is 3/8" diameter x 2 1/8" grip, with a turned groove on each end to accept 3/8" SS Snap Rings, K-63015 (2 included).
|
|
| SS Snap Rings for 3/8" Axle Pin: K-63015-2P: In 2-pack. Require small snap ring pliers for attachment.
|
|
| Outhaul (Lower) Sheave for D-Section Gooseneck: K-198-4A: Anodized aluminum sheave is 1" OD x 7/16" wide x 1/4" ID.
|
|
| Outhaul (Lower) Sheave Axle for D-Section Gooseneck: K-10478: SS axle pin is 1/4" diameter x 13/16" grip, with a turned groove on each end to accept 1/4" SS Snap Rings, K-63016, above (2 included).
|
|
|
|
|
| New-Style Double Reef Cam Conversion Kit for D-Section: K-11442: | |
| Cam Conversion Kit for D-Section Gooseneck converts Old-Style Spring-Cam
arrangement to the New-Style friction cam assembly. Easily installed Kit includes everything
necessary
for 2 reef lines including Cam levers, adjustable friction washers, reef sheaves, SS spacers, Cover
plates,
bolts and locknuts. The only machining required is to drill the old-style 1/4" sheave axle (forward)
hole to 5/16".
Individual components are listed separately, See
Parts for New-Style D-Section Internal Gooseneck Assembly.
|
|
|
New-Style Port Reef Cam Conversion Kit for D-Section: K-11442P: New-Style Starboard Reef Cam Conversion Kit for D-Section: K-11442S: |
|
| Single Cam Conversion Kit for D-Section Gooseneck converts
Old-Style Spring-Cam arrangement to the New-Style friction cam assembly. Easily installed
Kit includes everything necessary for single reef line including Cam lever, adjustable
friction washers, reef sheave, SS spacer, Cover plate, bolts and locknuts. The only
machining required is to drill the old-style 1/4" sheave axle (forward) hole to
5/16". Specify Port or Starboard. Individual components are listed separately, See
Parts for New-Style D-Section Internal Gooseneck Assembly.
|
|
| New-Style Sheave Conversion Kit for D-Section: K-11442NC: Sheave Conversion Kit for D-Section Gooseneck converts Old-Style Gooseneck to the New-Style with Cover Plates, Sheaves, and No cams. Easily installed Kit includes everything necessary for leading reef lines down and aft, including (2) reef sheaves, (4) SS spacers, Port and Starboard Cover plates, bolts and locknuts. Individual components are listed separately, See Parts for New-Style D-Section Internal Gooseneck Assembly. As K-11442, above, but with 2 SS Spacers to replace the reef cams. The only machining required is to drill the old-style 1/4" sheave axle (forward) hole to 5/16". |
|
