| Spartan CD-1
Boom Section
CD-1 Boom Section - Clear Anodized: SP-CD1CA-___:
Spartan CD-1 Section Boom Tube is stocked in a
variety of lengths (listed above) fully anodized, it can also be cut to
shorter lengths. To
order, specify length.
Sections can also be milled for the sail entrance or
other components if necessary, painted finishes and other lengths are
available on special
order, Please specify. If you require a complete Boom Assembly, you can
select from
components below and contact us with specifications.
|
|
CD-1 Standard
Boom Hardware
Listed below are parts specific to the Spartan CD-1 Boom Section. There are many
parts for
specific configurations that are not listed here. If you require CD-1 Section
Boom
Components not listed here please contact us with details. Please note:
As principal dimensions of the Spartan Spar CD-1 Section are equivalent to those
of Kenyon
Spar's B-Section, all Kenyon B-Section
Boom
Components will also fit the CD-1 Boom Section.
All Aluminum Castings listed below are carefully hand finished and
coated with a baked-on
Black Epoxy (to retard corrosion) as Standard. Castings are available Clear
Anodized at
additional cost, add CA to part number.
|
|
| CD-1
Gooseneck Assemblies & Parts |
CD-1 Gooseneck Assembly Complete w/
1/2" Slide: SP-031FS:
Heavy-duty cast aluminum Gooseneck End incorporates a 1/4" tack pin and includes
fixed SS yolk, 3/4" SS Toggle, K-9267, and SS Gooseneck
Slide, SP-032. Fits CD-2, CD-3, and all mast sections using
3/8" or larger round slugs or boltrope.
p
|
|
|
CD-1 Gooseneck Assembly w/ Tack &
3/4" Toggle: SP-031F:
As SP-031FS (above), but without SS Gooseneck Slide, SP-032.
Toggle attaches directly to any gooseneck brackets designed for a 3/4" Toggle
with
1/4" Pin (see individual mast sections), as well as the SP-032,
and other gooseneck slides designed for 3/4" Toggles. |
|
|
CD-1 Gooseneck Casting w/ Tack: SP-031C:
Black Epoxy coated Gooseneck casting with tack pin only, as used in the
assemblies listed above.
p
|
|
|
SS Gooseneck Slide:
SP-032:
New Heavy-duty reinforced SS Gooseneck Slide accepts 3/4" SS Toggle, K-9267,
and has a welded ring for downhaul attachment. Includes 1/4" vertical pin. Fits
Spartan CD-1, CD-2, CD-3, and all mast
sections using 1/2" round slugs or boltrope.
K-9138A
p
|
|
|
SS Gooseneck Toggle - 3/4":
K-9267:
SS Gooseneck Toggle attaches directly to gooseneck brackets or gooseneck slides
designed
for a 3/4" toggle, and to any boom end casting using the K-79
or K8700A SS yoke assemblies. Toggle is 3/4" square x
7/8" long with 1/4" holes at 90 degrees to each other on 3/8" centers.
p
|
|
|
SS Yoke Assembly for 3/4" Toggle:
K-79A:
SS yoke attaches to Gooseneck Casting using a 1/4" bolt, locknut, and 1" OD
washer. Yoke is formed from 5/8" wide stock and is 1" wide (outside), and
13/16" wide (inside), 1/4" hole centers are 11/16" from bottom inside.
3/4" SS Toggle, K-9267, is attached with a 1/4" SS bolt and
locknut (included). |
|
CD-1 Roller Reefing Gooseneck Assembly
w/ 1/2" Slide: SP-031RS:
Heavy-duty cast aluminum Gooseneck End incorporates a SS spring loaded Roller
Reefing
assembly and 1/2" Slide. Spring-loaded roller-reefing mechanism works by pulling
aft
on the boom and turning it in 1/2 turn increments. SS yoke assembly is fixed in
a
rectangular recess until boom is pulled aft. SS Spring locks yoke into recess
when boom is
released. Works only with end-boom sheeting systems with swiveling mainsheet and
topping
lift attachments. Cast aluminum boom end fitting includes captive 1/4" SS tack
pin
and SS Roller-Reefing yoke assembly with 3/4" SS Toggle and SS gooseneck
Slide, SP-032.
Fits all mast sections using 3/8" or larger round slugs or boltrope.
p
|
|
|
CD-1 Roller-Reefing Gooseneck
Assembly w/ 3/4" Toggle: SP-031R:
As SP-031RS (above), but without SS Gooseneck slide,
SP-032.
Toggle attaches directly to any gooseneck brackets designed for a 3/4" Toggle
with a
1/4" Pin (see individual mast sections), as well as the SP-032,
and other gooseneck slides. Roller-Reefing mechanism requires use of Outhaul End
with
pivoting tangs, SP-033-2, or similar. |
|
|
CD-1 Gooseneck Casting with Tack: SP-031C:
Black Epoxy coated Gooseneck casting with tack pin only, as used in the
assemblies listed above.
p
|
|
|
SS Gooseneck Slide:
SP-032:
New Heavy-duty reinforced SS Gooseneck Slide accepts 3/4" SS Toggle, K-9267,
and has a welded ring for downhaul attachment. Includes 1/4" vertical pin. Fits
Spartan CD-1, CD-2, CD-3, and all mast
sections using 1/2" round slugs or boltrope.
K-9138A
p
|
|
|
SS Gooseneck Toggle - 3/4":
K-9267:
SS Gooseneck Toggle attaches directly to gooseneck brackets or gooseneck slides
designed
for a 3/4" toggle, and to any boom end casting using the K-79
or K8700A SS yoke assemblies. Toggle is 3/4" square x
7/8" long with 1/4" holes at 90 degrees to each other on 3/8" centers.
p
|
|
|
SS Roller-Reefing Yoke Assembly for
3/4" Toggle: K-8700A:
SS spring-loaded roller-reefing yoke assembly for use with boom end castings
that have a
3/8" hole centered in a 1" x 3/4" rectangular recess. Attaches to 3/4"
SS Toggle, K-9267, with a 1/4" SS bolt and locknut
(included). Post is 3/8" diameter x 3" long. Includes SS Spring, (2) SS washers,
and cotter pin.
p
|
|
|
| CD-1
Outhaul Assemblies & Parts |
|
CD-1 Outhaul Casting: SP-033:
Heavy-duty Black Epoxy coated cast aluminum Outhaul End has tab with 2
holes for outhaul, and/or topping lift attachment.
p
|
|
|
CD-1 Outhaul Assembly w/ One Tang: SP-033-1:
Heavy-duty cast aluminum Outhaul End with attachment points for outhaul and
topping lift.
Includes single pivoting tang for mainsheet or topping lift attachment.
p
|
|
CD-1 Outhaul Assembly w/
Two Tangs: SP-033-2:
Heavy-duty cast aluminum Outhaul End with attachment points for outhaul and
topping lift.
Includes two pivoting tangs for mainsheet and topping lift attachment. For use
with roller
reefing gooseneck, SP-031R.
p
|
 |
|
Mainsheet Tang for CD-1 Boom:
SP-260:
Flat Mainsheet Tang attaches to Boom end casting using a 3/8" bolt. For use with
Spartan CD-1, Kenyon B-Section, and similar sized booms. Mainsheet
Tang
is 3 1/2" long x 1" wide x .076" thick with (1) 3/8" mounting
hole and (1) 5/8" hole for attachment of Mainsheet block. Hole centers
are 2
1/2" apart.
Sch 85-70
|
|
|
| CD-1 Boom
Accessories |
Outhaul Slides
A variety of Outhaul Slides are available to fit the 1/2" Boltrope groove in the
CD-1
Boom Section. See
Outhaul Slides for 1/2" Boltrope Groove.
|
Boom Bail - 1/2" Strap x
2 1/2" long: K-291A:
SS Boom Bail is a lightweight formed-strap design, which can be easily contoured
to fit a
variety of smaller sections. Bail is 1/2" wide x 1/16" thick, and 2 1/2"
long. Fastens with (4) 3/16" (#10) fasteners. |
|
Boom Bail - 1/2" Strap x
3 1/2" long: K-291B:
SS Boom Bail is a lightweight formed-strap design, which can be easily contoured
to fit a
variety of smaller sections. Bail is 1/2" wide x 1/16" thick, and 3 1/2"
long. Fastens with (4) 3/16" (#10) fasteners. |
|
Boom Bail - 1/4" x 1 3/4"
wide: K-S9001:
SS Boom Bail made from 1/2" x 1/16" strap is designed to be attached with (1)
1/4" SS bolt and nut. Formed at 1 3/4" wide, width can be varied to fit larger
or smaller sections. Bail length, from bolt center, is 2 1/2". For use with
CD-1
Boom.
p
|
|
|
Boom Bail Bolt Assembly - 1/4" for
CD-1 Boom: K-S9001BA:
Boom Bail bolt assembly includes 1/4" SS bolt x 2 1/4", with locknut, and nylon
washers to prevent bail from damaging boom surface as it pivots. |
|
Boom Vang Ball Attachment
Plate for CD-1 Boom: K-2182:
Formed SS plate for attachment of Boom Vang with 1/8" wire swage
ball.
Allows for quick attachment and removal of Boom Vang, raised channel design
allows easy
installation without milling slot in boom. Channel projects approximately 3/8"
from
underside of Boom when installed. Formed Stainless Steel plate is 2" long x 1
7/8" high. Fastens with (6) 3/16" (#10) screws or rivets. |
|
|
Boom Vang Wire Pennant with Swage Ball: K-2182WP:
Wire Pennant for attachment of Boom Vang to Boom Vang Ball
Attachment Plate.
Pennant is 1/8" wire with swage ball and shank (MS20664-4)
on one end and a nicopress and thimble on the other. Thimble allows attachment
of any
upper Vang block. Assembly is 6" long. Ball is suitable for all Ball
Attachment Plates with a slot that is 1/4" wide or less. |
 |
Spar Cleat - 3" long:
SP-032C:
Cast Aluminum Spar Cleat is a low-profile design with a narrow base suitable for
use with
line up to 1/4" diameter. Black Epoxy Cleat is 3" long, and fastens to spar with
(2) 5/32" (#8) FH screws on 13/16" centers. |
|
Spar Cleat - 4" long:
D-10324:
Cast Aluminum Open Base Spar Cleat is a low-profile design with a narrow base
suitable for
use with line up to 3/8" diameter. Black Epoxy Cleat is 4" long, and fastens to
spar with (2) 3/16" (#10) FH screws on 1" centers. |
|
Cheek Block w/ Curved
Base: K-140X:
Cheek Block with curved base is used on smaller Booms for Outhaul and Reef
lines. SS Cheek Block has 1 1/16" OD Delrin Sheave suitable for use with line up
to
3/8" diameter. Base is 3 3/16" long x 7/8" wide, and fastens to spar with (4)
3/16" (#10) RH screws on 2 11/16" (horizontal) and 1/2" (vertical) centers.
|
 |
