Kenyon 6092 CR Mast Section

Common Mast usage: Alden 44; Aloha 41; Cal 39; Celestial 48K Main, 46K Main; Cheoy Lee 41, 43C, 44C; CSY 44; Endeavour 40, 43K; Freya 39; Golden Wave 38, 42; Gulfstar 40; Hans Christian 38, 43C, 43K Main; Hunter 45, 54; Hylas 44; Ingrid 38K Main; Lancer 42, 44; Lord Nelson 41; Morgan 382, 43; Passport 40, 42; Roberts 43K Main; S-2 11.0; Stamas 44 Main; US-42;

Kenyon 6092 Cruising Mast Section 6092 Mast Section - Clear Anodized: K-X6092CA-___: 6092 Mast Section - Raw: K-X6092R-___: Kenyon 6092 Section Mast Tube is stocked in a variety of lengths (listed above) fully anodized or raw (mill finish), it can also be cut to shorter lengths. To order, specify length. Sections can also be milled for the sailgate or other components, painted finishes and other lengths are available on special order, Please specify. If you require a complete Mast Assembly, you can select from components below and contact us with specifications. Kenyon Cruising Sections feature an interchangeable Luff Track system, which covers a channel designed to secure any electrical wiring. Select from a variety of Cruising Section Luff Tracks. This system provides easy access to all electrical wires, keeping them from banging around and isolating them from any internal halyard damage, as well as allowing easy conversion of existing masts to different mainsail slide systems.

6092 Standard Mast Hardware Listed below are parts specific to the Kenyon 6092 Mast Section. For more generic parts, see Kenyon Exit Blocks, Kenyon Exit Plates, Kenyon Shroud Tangs , and other categories listed under Kenyon Spar Parts. There are many parts for specific configurations that are not listed here. If you require 6092 Mast Components not listed here please contact us with details.

Mastheads: Kenyon mast sections for larger boats use welded-in mastheads for maximum strength and durability with minimum weight. A variety of masthead configurations are available with a new spar or a replacement tube. Listed below are the standard weld-in mastheads for the Kenyon 6092 Cruising Mast Section, and parts for them. Custom mastheads are available as well, please inquire.
Heavy Duty Masthead Assembly for Masthead Rig: K-40551: Weld-in aluminum Masthead Assembly for untapered 6092 mast section incorporates (4) 3 3/4" dia. aluminum sheaves, *K-10556, for internal or external wire or rope halyards. Includes 5/8" pins for attachment of slotted SS toggles for headstay and backstay (order separately), and 3/8" pins for triatic stay and topping lift attachment. Masthead features 2 extended Spinnaker Cranes, pre-drilled for attachment of Spinnaker Halyard Bail K-11302* (order separately).
Heavy Duty Masthead Assembly for Masthead Rig: K-40551-1: As K-40551 (above), but with only (1) Spinnaker Crane for reduced weight and windage.
	Masthead Toggle w/ 5/8" Pin: K-40552: Slotted SS Toggle Assembly for 6092 Masthead, K-40551, includes 5/8" lower pin, and is designed to sit on 5/8" upper pin. Toggle measures 1 7/8" wide x 3/16" thick x 2 3/4" between pin centers, and will accommodate eyes up to 3/4" thick. Slot is 7/16" wide x 2 1/2" deep. 6092o, 68106, K-10564A
	3 3/4" OD Aluminum Sheave: K-10556: Lightweight cast anodized aluminum sheave with integral bronze bushing is 3 3/4" OD x 3/4" wide x 1/2" ID. With wire/rope V-groove for up to 5/8" line and 1/4" wire, unit features recessed walls to minimize weight. As used in a variety of Mastheads.
	Masthead Sheave Pin: K-11129-1: SS Masthead Axle/Sheave Pin has thin stem welded to teardrop tab which attaches to mast with (1) #10 screw. Pin measures 1/2" x 3" long (P208-97).
	Masthead Sheave Pin: K-11129-2: SS Masthead Axle/Sheave Pin has thin stem welded to teardrop tab which attaches to mast with (1) #10 screw. Pin measures 1/2" x 3 1/2" long (P208-113).
	Masthead Sheave Pin: K-11129-3: SS Masthead Axle/Sheave Pin has thin stem welded to teardrop tab which attaches to mast with (1) #10 screw. Pin measures 1/2" x 3 3/4" long (P208-121).
	Masthead Sheave Pin: K-11129-4: SS Masthead Axle/Sheave Pin has thin stem welded to teardrop tab which attaches to mast with (1) #10 screw. Pin measures 1/2" x 4 1/2" long (P208-145).
	Masthead Spinnaker Bail: K-11302: Heavy 3/8" SS bail is welded to a flat plate which bolts to the top of the masthead with (4) 5/16" x 3/4" screws and locknuts. Plate measures 2 1/4" long x 2 5/8" wide. Screw hole spacing (to centers) is 13/16" fore and aft x 1 1/8" wide. Bail is angled downward and projects 1 3/4" forward of plate. Mounting requires drilling (4) 5/16" holes. Designed for use with *K-40551* Masthead Assembly on Kenyon 6092 mast. Attaches with (4) 5/16" x 3/4" screws and locknuts.
	Chafe Cage for Heavy Duty Masthead Assembly: K-11627: Optional Stainless Steel welded Chafe Cage is used on underside of K-40551 Mastheads to provide additional chafe protection for halyards. Attaches with (2) #10 screws.

Staysail Attachments: The Kenyon 6092 mast section is used with a variety of attachments for Staysail Stays, Baby Stays, Pole lifts, etc. For additional Items, See Forestay / Staysail Tangs.
Staysail / Inner Forestay Attachment for 1/2" Pin: K-19060-8: Staysail / Inner Forestay Attachment for 5/8" Pin: K-19060-10: SS Staysail/Forestay Tang has 1/2" or 5/8" Pin hole for Forestay attachment and 3/8" x 3/4" slot for halyard block shackle. Heavy 1/4" nose is welded to plate formed to fit 6092 Mast Section. Base is 4 1/2" high x approximately 3 1/2" wide and attaches to mast with (8) 1/4" fasteners. For 6092 and similar sections.
*Welded Forestay/Staysail Stay & Halyard Block Tang for 1/2" Pin: K-11505:* *Welded Forestay/Staysail Stay & Halyard Block Tang for 5/8" Pin: K-11505-1:*
Heavy aluminum Forestay/Staysail Stay & Halyard Block Tang for weld-on applications. Double-nosed Tang has 1/2" or 5/8" hole for Forestay Toggle above a 1/2" x 7/8" slot for attachment of a halyard block shackle. Contoured Tang is 9" long x 1/2" thick, and projects (maximum) 2 7/8" forward of mast. Designed for welding to mast surface, Tang is cut from 6061-T6 aluminum plate with mill finish. BF-536

Spreaders: The Kenyon 6092 mast section is normally used with Kenyon SP-4, or SP-5 airfoil spreaders. A variety of Spreader Brackets, welded Spreader Bases, and Spreader Bars are available. For Spreader details, or to order replacement Spreaders, see Kenyon Spreader Sections.
6092 Weld-on Spreader Bracket Ass'y for SP-4: K-11479K: Aluminum weld-on Spreader Bracket Assembly for 6092 mast section. Set of 2 aluminum plates is contoured to fit curvature of Kenyon 6092 Mast Section, and designed to be welded to Port or Starboard side. Normally plates are welded at a 5-7 degree angle up, with 1/2" between them to accommodate spreaders with an inboard end of 3/8" thick plate. Upper bracket plate (without holes) is drilled after welding, using Lower plate (with holes) as a drill guide, assuring accurate alignment regardless of angle. Lower plate has (2) 3/8" holes on 3 1/2" centers for use with standard SP-4 Spreader Inboard End, K-11480-4. Contoured plates are (maximum) 6 3/4" wide x 2 3/8" deep x 3/8" thick. Plates have mill finish for ease of welding, and are notched on the mast centerline for ease of placement. One (1) set is required for each side of mast. As used on Hunter 54. *M
6092 Weld-on Spreader Bracket Ass'y - 30� aft: K-11479K-30: Aluminum weld-on Spreader Bracket Assembly for 6092 mast section. Set of 2 aluminum plates is contoured to fit curvature of Kenyon 6092 Mast Section, and designed to be welded to Port or Starboard side. Normally plates are welded at a 5-7 degree angle up, with 1/2" between them to accommodate spreaders with an inboard end of 3/8" thick plate. Upper bracket plate (without holes) is drilled after welding, using Lower plate (with holes) as a drill guide, assuring accurate alignment regardless of angle. Lower plate has (2) 3/8" holes on 3" centers for use with 30 degree aft Spreader Inboard Ends for SP-4 Spreaders, K-11663ML, or SP-5 Spreaders, K-11840-5-30. Contoured plates are 5" wide x (maximum) 4 1/4" long x 3/8" thick. Plates have mill finish for ease of welding, and are notched on the mast centerline for ease of placement. One (1) set is required for each side of mast. As used on Hunter 45. *M
6092 Weld-on Spreader Bracket Ass'y for SP-5: K-11630K: Aluminum weld-on Spreader Bracket Assembly for 6092 mast section. Set of 2 aluminum plates is contoured to fit curvature of Kenyon 6092 Mast Section, and designed to be welded to Port or Starboard side. Normally plates are welded at a 5-7 degree angle up, with 1/2" between them to accommodate spreaders with an inboard end of 3/8" thick plate. Upper bracket plate (without holes) is drilled after welding, using Lower plate (with holes) as a drill guide, assuring accurate alignment regardless of angle. Lower plate has (2) 3/8" holes on 4 3/4" centers for use with standard SP-5 Spreader Inboard End, K-11480-5. Contoured plates are (maximum) 6 3/4" wide x 2 3/8" deep x 3/8" thick. Plates have mill finish for ease of welding, and are notched on the mast centerline for ease of placement. One (1) set is required for each side of mast. As used on Endeavour 40, Hunter 54 and others.
6092 Weld-on Spreader Bracket Ass'y for SP-5: K-11630K-SN: Special Aluminum weld-on Spreader Bracket Assembly for 6092 mast section. As K-11630K, above, but Lower plate has (2) 3/8" holes on 4 1/4" centers for use with SP-5 Spreader Inboard End, K-11480-5SN. As used on Stamas 44, and others.

Winch Pad for 6092: K-10648: Black Urethane Winch Pad is 6 1/8" dia., and molded to fit on centerline of 6092 section. Pad insulates winch from mast wall and properly seats it for mounting. Pad is attached to mast with 1 screw, holes for screws to mount winch are then drilled through pad and tapped in mast wall. *
Forward Offset Winch Pad for 6092: K-11100: Black Urethane Winch Pad is 5 3/4" dia., and molded to fit 2" forward of centerline on 6092 section. Used primarily for staysail and spinnaker halyard winches. Pad insulates winch from mast wall and properly seats it for mounting. Pad is attached to mast with 1 screw, holes for screws to mount winch are then drilled through pad and tapped in mast wall.
7/8" Sail Slide Stop: K-10424L: SS Spring Pin Sail Slide Stop fits all mast sections with track for 7/8" or 15/16" internal flat slides. Superior design allows Slide Stop to remain captive in mast track. Gate cutout (1 3/4" high) is made just 1" above SS Gooseneck bracket. Spring pin fits in 1/4" hole drilled at top of cutout, and slides down into recess beneath Gooseneck Bracket when Spring pin is pulled. This design allows sail slides to come as close as possible to the gooseneck while remaining in track, and eliminates problems associated with slides snagging while going past a normal sail gate. Plate is 2 1/2" long with a 1/4" spring pin. For use with *K-73540* flat internal luff track.

Gooseneck / Vang Bracket w/ Bail: K-10580: Designed for use with the *K-10345* Gooseneck Toggle/Tack Assembly for E-Section and larger Booms, this SS welded Bracket takes a 3/8" Vertical pin, K-CP6-76, and has clearance for a 1 1/2" Toggle. Fastens to 6092 Mast Section with (8) 1/4" (6mm) fasteners and includes welded 5/16" bail for mainsheet turning block. Base is 5" vertical x approximately 4" wide. Can also be used as Vang Bracket with addition of appropriate Vang Toggle, below.
	Gooseneck Clevis Pin - 3/8": K-CP6-76: Vertical Clevis Pin for use with *K-10580* Gooseneck Bracket. SS pin is 3/8" dia. with 2 3/8" grip length.
	Gooseneck Toggle/Tack Ass'y w/ Reef Hooks: K-10345A: Used with *K-10580* gooseneck bracket, this combination toggle/tack/reef assembly features 3 tack positions and includes 3/8" tack fastpin, K-10557. *Takes 3/8" vertical and* horizontal pins.** Two reef hooks allow for ease of reefing from either side of the boom. Toggle portion is 1 1/2" high x 7/8" wide with 1" between pin centers. Unit (excluding Reef Hooks) is 4" high x 7/8" wide x 2 1/4" long. Attaches directly to any of the Kenyon SS Gooseneck Brackets designed for a 1 1/2" Toggle with 3/8" vertical pin. Fits E section, 3550, and 3756 standard boom goosenecks.
	Tack Fastpin for 1 1/2" Toggle: K-10557 (FP-6-32): SS Fastpin is 3/8" dia. x 1" long. Used in 1 1/2" Toggle/Tack/Reef Hook Assembly K-10345.
	Vang Toggle: K-10963: Used with the *K-10580* Gooseneck Bracket, this SS toggle results in a fully pivoting vang bracket to minimize working stresses. Large 3/4" horizontal hole allows for attachment of any shackle or block.
	*Vang Toggle w/ 14mm Pin hole: K-10963-2:* Welded SS Vang Toggle for use with any Kenyon Gooseneck Bracket with a 3/8" Pin. SS tube is 1 1/2" long with Bronze bushed hole for 3/8" Vertical Pin. Welded SS Tab is 5mm (3/16") thick and projects 2 3/8" (60mm) out from tube. Tab has 14mm (9/16") hole for attachment of Vang and 8mm (5/16") hole for attachment of Vang Tackle. As used with Sparcraft Pneuvang and others.
	*Vang Toggle for Hard Vang: K-11788:* Used with the *K-10580* and other Kenyon Gooseneck Brackets with a 3/8" Pin, this SS toggle has (1) 9/16" (14mm) hole for Vang attachment and (3) 5/16" (8mm) holes for blocks. As used with Sparcraft Pneuvang and others.

Heavy Duty Gooseneck Bracket: K-10776: Designed for use with the *K-10702* gooseneck Toggle/Tack assembly, and large Kenyon 5072 boom section. SS welded bracket for 6092 mast section takes a 1/2" vertical pin and has clearance for up to a 3 1/4" toggle. Base is 6" vertical x approximately 5" wide, and attaches to the mast with (10) 1/4" fasteners. Can also be used as *Vang Bracket* with addition of appropriate Vang Toggle.
Heavy Duty Gooseneck Bracket w/ Bail: K-11120: Designed for use with the *K-10702* gooseneck Toggle/Tack assembly, and large Kenyon 5072 boom section, this SS welded bracket for 6092 mast section also has welded 5/16" bail for mainsheet turning block. Takes a 1/2" vertical pin and has clearance for up to a 3 1/4" toggle. Base is 6" vertical x approximately 5" wide, and attaches to the mast with (10) 1/4" fasteners. Can also be used as *Vang Bracket* with addition of appropriate Vang Toggle.
	Gooseneck Clevis Pin - 1/2": K-CP8-140: Vertical Clevis Pin for use with *K-10776* Gooseneck/Vang Bracket. SS pin is 1/2" dia. with 4 3/8" grip length.
	Gooseneck Toggle/Tack Ass'y w/ Reef Hooks: K-10702A: Used with *K-10776* gooseneck bracket, and large Kenyon 5072 boom section, this combination Toggle/Tack/Reef Hook Assembly features 2 Reef Hooks and includes 1/2" tack fastpin, K-10718. Takes 1/2" vertical and 5/8" horizontal pins. Two reef hooks allow for ease of reefing from either side of the boom. Toggle portion is 3" high x 1 3/8" wide with 1" between pin centers. Unit (excluding Reef Hooks) is 7 1/4" high x 1 3/8" wide x 3" long, Tack Pin is 3/4" forward of, and 4 3/4" higher than Horizontal pin. Attaches directly to any Kenyon and other SS Gooseneck Brackets designed for a 3" Toggle with 1/2" vertical pin.
	Tack Fastpin for K-10702 Toggle: K-10718 (FP-8-48): SS Fastpin is 1/2" dia. x 1 1/2" long. Used in K-10702 Toggle/Tack/Reef Hook Assemblies.
	*Vang Toggle for Hall 'C' Quikvang Vang: K-11789-C:* Used with *K-10776* and K-11120 Gooseneck Brackets, Toggle has (1) 5/8" (16mm) hole for Vang attachment and attaches to Bracket with a 1/2" Bolt. Aluminum Toggle is 3 1/4" high x 5/8" wide at 5/8" Pin hole. As used with Hall 'C' Quikvang and others.
Vang Toggle for Rigid Vang – Special: A variety of semi-custom Toggles, or Bracket/Toggle combinations are available to fit rigid (or solid) vangs produced by a number of manufacturers. Please specify manufacturer, model and Pin size.

Mast Boot for 6092 Standard Deck Collar: K-11261BS: White PVC Mast Boot helps prevent leakage at the deck. Slid over mast prior to stepping, it is then secured with a hose clamp on *K-11261-1* deck collar and one around the mast. One piece molded construction for optimum fit.
	6092 Mast Boot Clamp: MBC 21-31: All Stainless Steel Clamp for use with any Mast Boot on Kenyon 6092 Mast.
	6092 Deck Collar Boot Clamp: MBC 21-31: All Stainless Steel Clamp for use with Mast Boots on all Kenyon 6092 Deck Collars. 15
6092 Deck Collar, Standard: K-11261-1: Standard 6092 Deck Collar, for keel stepped masts, fastens to deck with (8) 5/16" bolts or screws. Base size (max.) is 13 7/8" x 10 5/8" x 1" high, with 1/4" thick flanges. Cast in 356 Aluminum with clear anodized finish. For use with standard Kenyon mast wedge K-77509-27. Shown with Mast Boot, K-11261B, and Clamps.
Mast Wedge for 6092 Deck Collar: K-77509-27: Extruded rubber Mast Wedge with flange provides even loading all around the mast. One-piece construction is far superior to individual wedges, which cause point loading leading to deformation. Cut to length for use with 6092 Deck Collars.
Low-Profile Deck Collar Assembly for 6092: K-10947: Low-profile 6092 Deck Collar Assembly, for keel stepped masts. Deck Collar Rings are bolted together (with Deck in between), using (8) 5/16" bolts and nuts. Mast Support Tabs bolt through Collar Rings, 3/8" bolt is later installed through Mast and Support Tabs preventing the deck from rising under rigging loads. Base size is 12 1/2" x 9 1/4" x 3/4" high. Kit includes (2) K-10927 Low-profile 6092 Deck Collar Rings, (2) K-10931 Mast Support Tabs, (1) 3/8" x 8" bolt with locknut, and the K-77509-27 rubber Mast Wedge. Original Assemblies used the *K-10769* Urethane Mast Collar (no longer available), as shown, which mounted between deck and upper Deck Collar Ring, requiring removal of Deck Collar Rings when unstepping the mast.
	*Low-Profile Deck Collar Ring only for 6092: K-10927:* Low-profile 6092 Deck Collar Ring fastens to deck with (8) 5/16" bolts or screws. Base size is 12 1/2" x 9 1/4" x 3/4" high. Cast in 356 Aluminum with black epoxy finish. *
	*Urethane Mast Collar for 6092 Low-Profile Deck Collar: K-10769:*
	Black Urethane Mast Collar with flange for 6092 Deck Collar Assembly. Unit mounts between deck and upper Deck Collar Ring. One piece molded construction requires that unit be slipped onto Mast (with Upper Deck Collar Ring) before stepping. Formerly supplied with Low-profile 6092 Deck Collar Assembly K-10947. This item is no longer available, having been replaced by the K-77509-27 Rubber Mast Wedge, shown above. When replacing this item with the K-77509** Rubber Mast Wedge, the Aluminum Deck Collar Rings are permanently bolted to the Deck (inside and out), and the Rubber Mast Wedge is installed after the Mast is stepped, greatly simplifying Mast stepping.
	Mast Support Tab for Low-Profile Deck Collar: K-10931: Support Tab fastens through deck collars with (2) 5/16" bolts, and through mast with 3/8" thru-bolt. Cast in 356 Aluminum with black epoxy finish.

Electrical Access Plate: RR-72-99: This 4 1/2" x 2" SS plate is designed to cover a 3" x 1 1/4" vertical slot in the side of the mast, just above the top of the mast step. Attaches with (4) 1/4" RH screws and saves much in frustration and money by allowing you access to the electrical plugs above the mast step without having to unstep the mast.

Mast Step Casting: K-10558: Mast Step for Kenyon 6092 fastens to deck or keelson with (4) 1/2" bolts in internal adjustment slots to allow for precise positioning. Unit is (maximum) 9 5/8" long x 6 3/8" wide. Cast in 356 Aluminum with black epoxy finish.

Your cart

Spars, Rigging, and Hardware for Sailboats