Kenyon 2333 Boom Section


2333 Internal Gooseneck Assemblies
The Kenyon 2333 Internal Gooseneck Assembly allows easy control of two internal lines. A variety of configurations are available to allow 2 internal lines to exit the gooseneck and be led back along boom, down to the deck, or cleated at the gooseneck using lever action cams.
2333 Internal Gooseneck Assembly w/ Toggle/Tack fitting: K-11723A: Cast aluminum gooseneck assembly incorporates provisions for internal outhaul and 1 internal reef line. Outhaul line exits on starboard bottom through delrin sheave, K-11726, and can run straight down to the deck, or back along boom bottom to a cleat. Reef line runs over delrin sheave, K-11726-1, past lever action cam, K-11246S, on port side, and down. Includes SS combination Toggle/Tack/Reef Hook Assembly K-10518A. Toggle attaches to any Kenyon gooseneck bracket designed for 1 1/2" toggle and 1/4" vertical pin. Vertical pin, K-CP4-61, is not included. Distance from vertical Toggle Pin to boom tube is 4 1/2". Parts for 2333 Internal Gooseneck Assemblies.
2333 Internal Gooseneck Assembly: K-11723: Cast aluminum gooseneck assembly, as K-11723A, above, but without SS combination Toggle/Tack/Reef Hook Assembly, K-10518A. Distance from horizontal Pin hole to boom tube is 3 1/2". Parts for 2333 Internal Gooseneck Assemblies.
2333 Internal Gooseneck Assembly w/ 2 Cams: K-11723-2C: Cast aluminum gooseneck assembly incorporates provisions for 2 internal lines with Lever Cams. Both lines runs over delrin sheaves, *K-11726-1, past lever action cams, K-11246S&P, and down. For use with K-10518A* or other Toggles up to 11/16" wide. Parts for 2333 Internal Gooseneck Assemblies.
2333 Internal Gooseneck Assembly without Cams: K-11723-2S: As K-11723, above, but with 2 Sheaves (K-11726) and no reef cams. Both internal lines can run straight down to the deck, or back along boom bottom to a cleat, or one of each. For use with K-10518A or other Toggles up to 11/16" wide. Parts for 2333 Internal Gooseneck Assemblies.
	2333 Internal Gooseneck Casting Only: K-11549: Finished Casting only as used in K-11723 Internal Gooseneck Assemblies, above.
*Gooseneck Toggle/Tack Assembly w/ Reef Hooks: K-10518A:* Used with any Kenyon gooseneck bracket for 1 1/2" toggle, and Kenyon 2333 or "D" section internal boom, this combination Toggle/Tack/Reef Hook Assembly features 3 tack positions and includes 3/8" tack fastpin, *K-10399.* Takes 1/4" vertical pin and 3/8" horizontal pin. Two 1/4" reef hooks allow for ease of reefing from either side of the boom. Toggle portion is 1 1/2" high x 11/16" wide with 1" between pin centers. Unit (excluding Reef Hooks) is 4" high x 11/16" wide x 2 1/4" long.
*Gooseneck Toggle/Tack Ass'y: K-10518N:* As *K-10518A, above, but without reef hooks. This combination Toggle and Tack Assembly features 3 tack positions and includes 3/8" tack fastpin K-10399.* Takes 1/4" vertical pin and 3/8" horizontal pin. Toggle fits all Kenyon Mast Brackets and a variety of Gooseneck Slides designed for a 1 1/2" Toggle with a 1/4" vertical pin. Toggle portion is 1 1/2" high x 11/16" wide with 1" between pin centers. Unit is (maximum) 4" high x 11/16" wide x 2 7/8" long.
*Long Gooseneck Toggle/Tack Ass'y: K-10518E:* As *K-10518N, above, but modified to increase the Tack Setback by 1". Takes 1/4" vertical pin* and 3/8" horizontal pin. Toggle fits all Kenyon Mast Brackets and a variety of Gooseneck Slides designed for a 1 1/2" Toggle with a 1/4" vertical pin. Toggle portion is 1 1/2" high x 11/16" wide with 2" between pin centers. Unit is (maximum) 4" high x 11/16" wide x 2 7/8" long. Specially for use with Gooseneck Slide for 3/4" Internal Flat Track, PP-M6A, and as used on the Freedom 25. Sd516
	Tack Fastpin for 1 1/2" Toggle: K-10399 (FP-6-28): SS Fastpin is 3/8" dia. x 7/8" long. Used in 1 1/2" Toggle/Tack/Reef Hook Assemblies K-10518A, and K-10518N.
Vertical Gooseneck Pin for 1 1/2" Toggle: K-CP4-61: Clevis pin is 1/4" diameter x 1 7/8" long. Used to attach K-10518 Toggle/Tack/Reef Hook Assemblies to any Kenyon Gooseneck Bracket or Slide for 1 1/2" Toggle and 1/4" Pin.

2333 Internal Outhaul Assembly
*2333 Internal Outhaul Assembly: K-11722:* Cast aluminum boom end fitting has (2) 1 1/2" internal aluminum sheaves (K-10545) for 1/8" wire, or up to 5/16" line, and topping lift attachment point with a 1/4" hole. Cut away design allows for easy access to internal lines without removing assembly from boom. Casting extends 2 1/8" (maximum) aft of the boom tube.
	2333 Internal Outhaul Casting Only: K-11550: Finished Casting only as used in K-11722 Outhaul Assembly, above.
	2333 Internal Outhaul Sheave: K-10545: Anodized aluminum Sheave is 1 1/2" OD x 3/8" (.370") wide x 1/4" ID. As used in K-11722 Outhaul Assembly, above, and in other applications.
	2333 Internal Outhaul Sheave Axle: K-11729: SS knurled Sheave Axle pin is 1/4" diameter x 1 7/8" long. As used in K-11722 Outhaul Assembly, above.

2333 Boom Accessories
*Vang Bracket for 2333 Boom: K-1757M:* SS Vang Bracket is contoured to fit 2333 boom and has welded triangle with 1/2" hole for attachment of vang tackle. Fastens with (6) 3/16" (#10) fasteners.
Boom Bail - 1/4" x 2 1/4" wide: K-10456: Heavy SS Boom Bail made from 1/4" rod is designed to be attached with (1) 1/4" SS bolt and nut. Formed at 2 1/4" wide, width can be varied to fit larger or smaller sections. Bail length, from bolt center, is 2 1/2". For use with 2333 and D-Section booms.
Boom Bail Bolt Assembly: 1/4" for K-10456 Bail: K-10456BA: Boom Bail bolt assembly includes 1/4" SS bolt x 2 3/4", with locknut, and nylon washers to prevent bail from damaging boom surface as it pivots.
*Spar Cleat - 4" long: Ken D-10324:* Cast Aluminum Spar Cleat is a low-profile design with a narrow base suitable for use with line up to 3/8" diameter. Commonly used for Outhaul Line. Black Epoxy coated Cleat is 4" long, and fastens to spar with (2) 3/16" (#10) FH screws on 1 3/16" centers.
*Clam Cleat w/ Fairlead & Curved Base: K-9115X:* Clam Cleat with fairlead is used in place of standard Spar Cleat for frequent Outhaul adjustment in racing applications. Best mounted forward of an eyestrap (K-226) with small block (Har 082, or equivalent). Suitable for use with 1/8"-1/4" (3-6mm) line, black plastic unit fastens with (2) #8 x 3/4" FH Screws on 2 5/8" (66mm) centers. Unit measures 3 1/4" long x 11/16" wide (82x18mm). CL203 CC Jr.
*SS Eyestrap: K-226:* Small Stainless Steel Eyestrap is used for securing smaller items to boom. Attaches to Boom with (2) 3/16" (#10, 5mm) screws or rivets.
*Single Bullet Block: Har 082:* Small single Bullet Block is used for the Outhaul line on the bottom of the Boom. Plastic Ball-Bearing Block has 1 1/8" OD Delrin Sheave suitable for use with line up to 5/16" diameter. Use with K-226 Eyestrap and K-9115X Clam Cleat, above.
*Cheek Block w/ Curved Base: K-140X:* Cheek Block with curved base is used on smaller Kenyon Booms for Outhaul and Reef lines. SS Cheek Block has 1 1/16" OD Delrin Sheave suitable for use with line up to 3/8" diameter. Base is 3 3/16" long x 7/8" wide, and fastens to spar with (4) 3/16" (#10) RH screws on 2 11/16" (horizontal) and 1/2" (vertical) centers.

Your cart

Spars, Rigging, and Hardware for Sailboats

Kenyon Spars 2333 Boom Section Measurements (outside): 3.30" x 2.29" (84mm x 58mm) Wall Thickness: .075-.095" Weight/ft.: .92 lbs. Moments of inertia: Ixx = .98", Iyy = .51" Circumference: 9 1/4" Sail slides: 3/8" round slugs (A017, A117) or 3/8" boltrope Alloy: 6061-T6 Standard Boom Lengths: 10' Common Boom usage: Impulse 21; See Also: Kenyon Spars 2333 Mast

Kenyon 2333 Boom Section 2333 Boom Section - Clear Anodized: K-2333CA-___: Kenyon 2333 Section Boom Tube is stocked in a variety of lengths (listed above) fully anodized, it can also be cut to shorter lengths. To order, specify length. Sections can also be milled for the sail entrance or other components if necessary, painted finishes and other lengths are available on special order, Please specify. If you require a complete Boom Assembly, you can select from components below and contact us with specifications.

Kenyon 2333 Boom Hardware Listed below are parts specific to the Kenyon 2333 Boom Section. For more generic parts, see Kenyon Exit Plates and other categories listed under Kenyon Spar Parts. There are many parts for specific configurations that are not listed here. If you require 2333 Boom Components not listed here please contact us with details.