 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Bronze T-Track |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Bronze T-Track |
|
|
|
|
| Bronze T-Track & End Stops |
| T-Track is essentially Flat Track with
an integral riser. Commonly used on deck for Jib and Genoa lead Cars and on the Mast for Spinnaker
and Gooseneck Slides, it allows for easily adjustable placement of load bearing fittings. Most
T-Track
has intermediate holes (between the fastener holes) for use with Spring Pin or Screw Pin stops.
Merriman Standard Extruded Bronze T-Track is listed below by size (Track width),
and length.
Aluminum T-Track is listed separately.
|
|
|
| Bronze T-Track | |
|
3/4" Bronze T-Track Other Bronze fittings used with this Track can be found under Genoa Cars and Spinnaker Cars. |
|
|
3/4" Bronze T-Track - 2 foot long: Mer 4471-2': 3/4" Bronze T-Track - 3 foot long: Mer 4471-3': 3/4" Bronze T-Track - 7 foot long: Mer 4471-7': 3/4" Bronze T-Track - 14 foot long: Mer 4471-14': 3/4" Bronze T-Track is an extruded T-Track that is 3/4" (22mm) wide with a 1/8" (3mm) thick flange, and is (maximum) 5/16" (8mm) high. Track is drilled for 1/4" (6mm) FH screws on 4" (102mm) centers, and has 1/4" diameter stop holes in between. * Due to hole spacing constraints, length tolerance is +/- 2 1/4". When ordered in pairs, both pieces will be the same length. If a precise length is required, please specify details. This item is not currently available.
|
|
| End Stop for 3/4" Bronze T-Track: Mer 4471S: Burnished cast Bronze End Stop for 3/4" T-Track fastens with a 1/4" (6mm) FH screw.
|
|
|
|
|
| 1" Bronze T-Track | |
|
1" Bronze T-Track - 2 foot long: Mer 4472-2': 1" Bronze T-Track - 3 foot long: Mer 4472-3': 1" Bronze T-Track - 7 foot long: Mer 4472-7': 1" Bronze T-Track - 14 foot long: Mer 4472-14': 1" Bronze T-Track is an extruded T-Track that is 1" (25mm) wide with a 1/8" (3mm) thick flange, and is (maximum) 3/8" (10mm) high. Track is drilled for 1/4" (6mm) FH screws on 4" (102mm) centers, and has 1/4" diameter stop holes in between. * Due to hole spacing constraints, length tolerance is +/- 2 1/4". When ordered in pairs, both pieces will be the same length. If a precise length is required, please specify details.
|
|
| End Stop for 1" Bronze T-Track: Mer 4472S: Burnished cast Bronze End Stop for 1" T-Track fastens with a 1/4" (6mm) FH screw.
|
|
| End Stop for 1" Bronze T-Track - Chrome: Mer 4472S-CR: Chrome-plated cast Bronze End Stop for 1" T-Track fastens with a 1/4" (6mm) FH screw. mil
|
|
|
|
|
| 1 1/4" Bronze T-Track | |
|
1 1/4" Bronze T-Track - 2 foot long: Mer 4473-2': 1 1/4" Bronze T-Track - 3 foot long: Mer 4473-3': 1 1/4" Bronze T-Track - 7 foot long: Mer 4473-7': 1 1/4" Bronze T-Track - 10 foot long: Mer 4473-10': 1 1/4" Bronze T-Track is an extruded T-Track that is 1 1/4" (32mm) wide with a 3/16" (5mm) thick flange, and is (maximum) 7/16" (11mm) high. Track is drilled for 5/16" (8mm) FH screws on 4" (102mm) centers, and has 3/8" diameter stop holes in between. * Due to hole spacing constraints, length tolerance is +/- 2 1/4". When ordered in pairs, both pieces will be the same length. If a precise length is required, please specify details.
|
|
|
End Stop for 1 1/4" Bronze T-Track: Mer 4473S: Burnished cast Bronze End Stop for 1 1/4" T-Track fastens with a 5/16" (8mm) FH screw.
|
|
|
End Stop for 1 1/4" Bronze T-Track - Chrome: Mer 4473S-CR: Chrome-plated cast Bronze End Stop for 1 1/4" T-Track fastens with a 5/16" (8mm) FH screw. |
|