 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Winch Pads |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Winch Pads |
|
|
|
|
| Z-Spar uses a variety of cast or formed aluminum Winch Pads (Winch
Brackets) the most common of which are listed here. If you require a Winch Pad not
listed below please specify Mast Section, and Winch Pad dimensions when inquiring. Standard Winch Pads |
|
|
|
| Standard Winch
Pads |
|
| Side Winch Pad: Z-1086: Cast aluminum Winch Bracket mounts to the side of Z145, Z170, Z190, Z230 and other Mast Sections. Winch mounting surface on Bracket is 3 1/2" (90mm) square. Bracket is 3 1/2" (90mm) wide x (maximum) 5 1/16" (130mm) high. Grey anodized Bracket is offset and fastens to Mast with four (4) 5mm (3/16") screws or rivets.
|
|
| Side Winch Pad: Z-1077: Cast aluminum Winch Bracket mounts to the side of Z265, Z301, Z351, Z401, Z501, Z531 and other Mast Sections. Winch mounting surface on Bracket is 5" (120mm) square. Bracket is 5" (120mm) wide x (maximum) 8" (200mm) high. Grey anodized Bracket is offset and fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Side Winch Pad: Z-1088: Cast aluminum Winch Bracket mounts to the side of Z601, Z701, Z901 and other Mast Sections. Winch mounting surface on Bracket is 5 3/4" (145mm) square. Bracket is 5 3/4" (145mm) wide x (maximum) 10" (250mm) high. Grey anodized Bracket is offset and fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Side Winch Pad: Z-151: Formed aluminum Winch Bracket mounts to the side of Z901, Z1101, Z1400 and other Mast Sections. Winch mounting surface on Bracket is 7 5/8" (195mm) square. Bracket is 7 5/8" (195mm) high x (maximum) 10 1/4" (260mm) wide. Clear anodized Bracket is 6mm (1/4") thick and fastens to Mast with twelve (12) 6mm (1/4") screws or rivets.
|
|
|
|
|
| Aft-Mount
Winch Pads for Reef Lines Aft-mount Winch Pads are made so that the bottom of the mounted winch will be angled at approximately 13� aft of the mast. This helps to align the winch for better use with Reefing Lines exiting from the forward end of the boom. |
|
| Aft Winch Pad: Z-1082: Cast aluminum Winch Bracket mounts to the aft side of Z265, Z301, Z351, Z401, Z-501, Z531 and other Mast Sections. Winch mounting surface on Bracket is 3 7/8" (100mm) square. Bracket is 3 7/8" (100mm) wide x (maximum) 6 13/16" (175mm) high. Grey anodized Bracket fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Aft Winch Pad: Z-1087: Cast aluminum Winch Bracket mounts to the aft side of Z601, Z701 and other Mast Sections. Winch mounting surface on Bracket is 4 7/8" (124mm) square. Bracket is 4 7/8" (124mm) wide x (maximum) 8 1/8" (206mm) high. Grey anodized Bracket fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Aft Winch Pad: Z-152: Aluminum Winch Bracket mounts to the aft side of Z901, Z1101 and other Mast Sections. Winch mounting surface on Bracket is 6 5/16" (160mm) wide x 7 1/2" (190mm) high. Bracket is 6 5/16" (160mm) wide x (maximum) 8" (203mm) high. Clear anodized, formed plate Bracket fastens to Mast with four (4) 6mm (1/4"), and two (2) 8mm (5/16") screws.
|
|
|
|
|
| Winch
Pads for Furling Masts |
|
| Side Winch Pad: Z-1086: Cast aluminum Winch Bracket mounts to the side of Z230E Furling Mast Section. Winch mounting surface on Bracket is 3 1/2" (90mm) square. Bracket is 3 1/2" (90mm) wide x (maximum) 5 1/16" (130mm) high. Grey anodized Bracket is offset and fastens to Mast with four (4) 5mm (3/16") screws or rivets.
|
|
| Side Winch Pad: Z-1077: Cast aluminum Winch Bracket mounts to the side of Z300E, Z400E, and Z500E Furling Mast Sections. Winch mounting surface on Bracket is 5" (120mm) square. Bracket is 5" (120mm) wide x (maximum) 8" (200mm) high. Grey anodized Bracket is offset and fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Side Winch Pad: Z-1088: Cast aluminum Winch Bracket mounts to the side of Z600E, Z700E, Z800E, and Z900E Furling Mast Sections. Winch mounting surface on Bracket is 5 3/4" (145mm) square. Bracket is 5 3/4" (145mm) wide x (maximum) 10" (250mm) high. Grey anodized Bracket is offset and fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Side Winch Pad: Z-151: Formed aluminum Winch Bracket mounts to the side of Z900E, Z1100E, and Z1400E Furling Mast Sections. Winch mounting surface on Bracket is 7 5/8" (195mm) square. Bracket is 7 5/8" (195mm) high x (maximum) 10 1/4" (260mm) wide. Clear anodized Bracket is 6mm (1/4") thick and fastens to Mast with twelve (12) 6mm (1/4") screws or rivets. |
|