 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Hinged Mast Steps |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Hinged Mast Steps |
|
|
|
|
| Z-Spar has produced an incredible variety of cast aluminum Standard and Tabernacle (hinged) Mast Steps. Most Hinged (Tabernacle) Mast Steps are listed below, for Standard (non-hinging) Mast Steps, See, Z-Spar Standard Mast Steps. If you require a Hinged Mast Step not listed below, please specify Mast Section and Mast Step description when inquiring. | ||
|
New-Style Hinged Tabernacle Deck Plates & Mast Feet Old-Style Hinged Tabernacle Deck Plates & Mast Feet Standard (non-Hinged) Mast Steps |
||
|
|
||
| New-Style Tabernacle Deck Plates and Mast Feet | ||
|
Deck Plate for Tabernacle Mast Step w/ 1/4" Pin: Z-1100A: Cast aluminum Deck Plate for use with Tabernacle Mast Foot on Z145, Z170, and Z190 Mast Sections. Features holes on each side for use with Z-250 turning blocks. Mast Foot hinges on 6mm pin (Z-1719), included, which goes through holes on aft side of Deck Plate. Deck Plate measures 4 7/8" (124mm) long, by 4 1/4" (108mm) wide and fastens to deck with (4) 1/4" (6mm) FH screws.
|
|
|
|
|
Tabernacle Hinge Pin – 6mm (1/4"): Z-1719: SS Hinge Pin for use with Z-1100 Deck Plate. Pin is 6mm (1/4") diameter with a 95mm Grip length.
|
|
|
|
Spacer for Z-1100 Deck Plate: Z-1100SP: Special high-density Spacer for use with Z-1100 Deck Plate. Plastic Spacer fits under Deck Plate, raising it 1 1/2" to make up for height lost when switching from Old-style Mast Foot with Sheaves, below. Spacer is drilled to match holes in Z-1100 Deck Plate.
|
|
|
Tabernacle Mast Foot for Z145: Z-1397: Cast aluminum Mast Foot for Z145 section hinges on 6mm pin (Z-1719) which goes through holes on aft side of Z-1100 Deck Plate. Unit may be labeled 1397.
|
||
|
Tabernacle Mast Foot for Z170: Z-1095: Cast aluminum Mast Foot for Z170 section hinges on 6mm (1/4") pin (Z-1719) which goes through holes on aft side of Z-1100 Deck Plate. Unit may be labeled 1011 and/or 1095.
|
|
|
| Tabernacle Mast Foot for Z190 - Small: Z-1096: Small Cast aluminum Mast Foot for Z190 section hinges on 6mm (1/4") pin (Z-1719) which goes through holes on aft side of Z-1100 Deck Plate. Unit is (maximum) 5" (127mm) long x 3 1/4" (82mm) wide. Unit may be labeled 1012 and/or 1096.
|
||
|
|
||
|
Deck Plate for Tabernacle Mast Step w/ 5/16" Pin: Z-1101A: Cast aluminum Deck Plate for use with Tabernacle Mast Foot on Z190, Z230 and Z265 Mast Sections. Features holes on each side for use with Z-261, Z-272 and Z-300 turning blocks, or Z-300SA Block Studs. Mast Foot hinges on 8mm (5/16") pin (Z-1316), included, which goes through holes on aft side of Deck Plate. Deck Plate measures 6" (152mm) long, by 5 1/8" (130mm) wide and fastens to deck with (4) 1/4" (6mm) FH screws.
|
 |
|
|
|
Tabernacle Hinge Pin – 8mm (5/16"): Z-1316: SS Hinge Pin for use with Z-1101 Deck Plate. Pin is 8mm (5/16") diameter with a 103mm Grip length.
|
|
|
Tabernacle Mast Foot for Z190 - Large: Z-1171: Large cast aluminum Mast Foot for Z190 section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit is (maximum) 5 1/4" (134mm) long x 3 1/4" (82mm) wide. Unit may be labeled 1012 and/or 1171.
|
||
| Tabernacle Mast Foot for Z230: Z-1097: Cast aluminum Mast Foot for Z230 section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit may be labeled 1014 and/or 1097.
|
||
| Tabernacle Mast Foot for Z230E: Z-4001: Cast aluminum Mast Foot for Z230E furling mast section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit may be labeled 4001.
|
 |
|
| Tabernacle Mast Foot for Z265: Z-1098: Cast aluminum Mast Foot for Z265 section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit may be labeled 1015 and/or 1098.
|
||
|
|
||
|
Old-Style Tabernacle Deck Plates and Mast Feet w/ Sheaves Old-Style Mast Feet with integral sheaves have been obsoleted. Some sizes and angles are available on a limited basis. |
||
| Old-Style Deck Plate for Z145 - Z190 Mast Foot w/ Sheaves: Z-1112: | ||
|
Aluminum Deck Plate fits Z145, Z170, and Z190 Mast Feet with Sheaves. Cast Plate measures 97mm (3
13/16") long
(on deck) x 60mm (2 5/16") wide, with vertical rib, and slot on aft side for 6mm pin. Attaches to
deck with (4)
6mm (1/4") FH screws on 32mm (1 1/4") x 79mm (3 1/8") centers.
|
 |
|
| Mast Foot w/ Sheaves for Z145: Z-145SF-20: |
 |
|
| Mast Foot w/ Sheaves for Z145: Z-145SF-30: | ||
| Mast Foot w/ Sheaves for Z145: Z-145SF-210: | ||
| Mast Foot w/ Sheaves for Z145: Z-145SF-10/245: | ||
|
Mast Foot w/ Sheaves for Z145: Z-145SF-10/290: Old-Style small Cast Aluminum Mast Foot with Sheaves for Z145 Mast and Z-1112 Deck Plate. Used with up to six (6) 28mm Sheaves, Z-1614, and 6mm knurled axle Pins in a variety of lengths. These Mast Feet are no longer available, See: Mast Foot Replacement Kit for Z145.
|
||
|
Mast Foot w/ Sheaves for Z170: Z-170SF-30: Old-Style small Cast Aluminum Mast Foot with Sheaves for Z170 Mast and Z-1112 Deck Plate. Used with up to six (6) 28mm Sheaves, Z-1614, and 6mm knurled axle Pins in a variety of lengths. This Mast Foot is no longer available, See: Mast Foot Replacement Kit for Z170.
|
||
| Mast Foot w/ Sheaves for Z190: Z-190SF-30: | ||
| Mast Foot w/ Sheaves for Z190: Z-190SF-210: | ||
| Mast Foot w/ Sheaves for Z190: Z-190SF-10/245: | ||
|
Mast Foot w/ Sheaves for Z190: Z-190SF-10/260: Old-Style small Cast Aluminum Mast Foot with Sheaves for Z190 Mast and Z-1112 Deck Plate. Used with up to six (6) 28mm Sheaves, Z-1614, and 6mm knurled axle Pins in a variety of lengths. These Mast Feet are no longer available, See: Mast Foot Replacement Kit for Z190.
|
||
| Mast Foot Replacement Kit for Z145: Z-145SF-SKit: | ||
| Mast Foot Replacement Kit for Z170: Z-170SF-SKit: | ||
|
Mast Foot Replacement Kit for Z190: Z-190SF-SKit: Replacement Kit for Old-Style small Mast Feet includes Z-1100A Deck Plate, above, with special high-density Spacer, Z-1100SP, and the proper size Mast Foot and rivets to go with it. This arrangement eliminates the need to shorten rigging required with the New-Style Tabernacle alone, while maintaining Boom height. Conversion requires a separate Exit Plate, Z-3273, for halyards cleated on the Mast. For each halyard that was led through the Old-Style Mast Foot to the deck, an Exit Plate, Z-3273, and a Turning Block, Z-250 will be required (order separately). Attaches to deck with (4) 6mm (6mm) FH screws using original hole spacing. To order, specify Mast Section.
|
||
|
|
||
| Old-Style Deck Plate for Z230, Z260 Mast Foot w/ Sheaves: Z-1112L: | ||
| Aluminum Deck Plate fits Z230 and Z260 Mast Feet
with Sheaves. Cast Plate measures 138mm (5 7/16") long x 78mm (3 1/16") wide,
with vertical rib and horizontal SS 8mm pin. Attaches to deck with (4) 6mm (1/4") FH screws.
|
 |
|
|
Mast Foot w/ Sheaves for Z230: Z-230SF-10/270: Old-Style large Cast Aluminum Mast Foot with Sheaves for Z230 Mast and Z-1112L Deck Plate. Used with up to six (6) 45mm Sheaves, Z-1616, and 8mm knurled axle Pins in a variety of lengths. This Mast Foot is no longer available, See: Mast Foot Replacement Kit for Z230.
|
||
|
Mast Foot Replacement Kit for Z230: Z-230SF-SKit: Replacement Kit for Old-Style Z230 Mast Feet includes Z-1101A Deck Plate, above, with special high-density Spacer, and the Mast Foot, Z-1097, and rivets to go with it. This arrangement eliminates the need to shorten rigging required with the New-Style Tabernacle alone, while maintaining Boom height. Conversion requires a separate Exit Plate, Z-3273, or Z-3272, for halyards cleated on the Mast. For each halyard that was led through the Old-Style Mast Foot to the deck, an Exit Plate and a Turning Block, Z-261, Z-272, or Z-300, or Z-300SA Block Stud will be required (order separately). Attaches to deck with (4) 6mm (1/4") FH screws, New Deck holes will have to be drilled.
|
||
|
Mast Foot w/ Sheaves for Z260: Z-260SF-30: Mast Foot w/ Sheaves for Z260: Z-260SF-10/230: Mast Foot w/ Sheaves for Z260: Z-260SF-10/260: Cast Aluminum Mast Foot with Sheaves for Z260 Mast and Z-1112L Deck Plate. Used with up to six (6) 45mm Sheaves, Z-1616, and 8mm knurled axle Pins in a variety of lengths. These Mast Feet are no longer available.
|
 |
|
|
|
||
|
Old-Style Deck Plate for Z260 Mast Foot w/ Sheaves: Z-1175X: Aluminum Deck Plate to fit old-style Z260 and other Mast Feet with Sheaves. Cast Plate measures 160mm (6 5/16") long x 120mm (4 3/4") wide x 22mm (7/8") thick, with fore and aft slot to accept rib in mast foot, and slot in aft side for 6mm hinge pin. Attaches to deck with up to (8) 6mm (1/4") FH screws. As used on early O'Day 272, and others. *
|
 |
|
|
Mast Foot w/ Sheaves for Z260: Z-260SF-10/2P: Cast Aluminum Mast Foot with Sheaves for Z260 Mast and Z-1175X Deck Plate. Used with up to six (6) 45mm Sheaves, Z-1616, and 8mm knurled axle Pins in a variety of lengths. As used on early O'Day 272, and others. *
|
 |
|
