|
|
| Spartan Spars 1 5/16" Round Spreader Section - SP-091 Measurements: 1 5/16" OD x 1 1/16" ID Wall Thickness: .133" Weight/ft.: .581 lbs. Alloy: 6061-T6 Stock Length: 19' Common Boat usage: Bristol 22, 24, 26, 27, 29, 29.9, 30*; C&C 24*, 26; Cape Dory 25D*, Cape Dory 26*, Cape Dory 27*, Cape Dory 28*, Cape Dory 30*; Pearson 22, 26, 27, 28, Electra, Ensign, Triton, and others. |
|
|
|
|
| 1 5/16" OD Round Spreader Tube | |
|
1 5/16" Round Spreader Tube: SP-091TC-___: Spartan 1 5/16" OD x 1 1/16" ID Spreader Tube (SP-091) is stocked in a clear anodized finish and is available in 3' 1" (37"), 4', 6', and 19' lengths, or can be cut to other lengths. To order: specify length.
|
|
|
|
|
| 1 5/16" OD Round Spreader Assemblies & Parts | |
|
1 5/16" OD Spreader Ass'y w/ Standard Tip x 38": SP-091AS: Standard Spartan SP-091 Round Spreader is 1 5/16" OD x 1" ID x 38" long (mast to wire) and has Aluminum Tip, SP-091T, with slot for upper shroud, and hole for seizing wire (included). Clear anodized 1 5/16" Standard Spreader Assembly is (maximum) 38 1/2" long.
|
|
|
1 5/16" OD Spreader Ass'y w/ Standard Tip - Special: SP-091A-___: Spartan SP-091 Round Spreader is 1 5/16" OD x 1 1/16" ID and has Aluminum Tip, SP-091T, with slot for upper shroud, and hole for seizing wire (included). Finished spreaders are available in any length, standard finish is clear anodized, specify color if painted finish is required. To order: specify maximum length from inboard end to shroud bearing surface, and finish.
|
|
|
1 5/16" OD Spreader Ass'y w/ Twist-Lock Tip x 37 1/2": SP-091ATLS: As Spartan SP-091AS, above, but with special 'twist-lock' Tip, SP-091TL, which secures Shroud without the use of seizing wire. Clear anodized 1 5/16" Spreader Assembly with Twist-Lock Tip is (maximum) 38 1/8" long.
|
|
|
1 5/16" OD Spreader Ass'y w/ Twist-Lock Tip: SP-091ATL-___: Spartan SP-091 Round Spreader with special Twist-lock Tip is 1 5/16" OD x 1 1/16" ID and has Aluminum Tip, SP-091TL, which secures Shroud without the use of seizing wire. Finished spreaders are available in any length, standard finish is clear anodized, specify color if painted finish is required. To order: specify maximum length from inboard end to shroud bearing surface, and finish.
|
|
|
1 5/16" OD Round Spreader Tip: SP-091T: Cast aluminum Spreader Tip for 1 5/16" OD x 1 1/16" ID Spreader features slot for up to 1/4" diameter shroud. Shroud is secured to Tip with seizing wire. Tip extends shroud seat 1 1/8" beyond spreader tube, unit projects 1 7/16" (maximum) beyond spreader tube.
|
|
|
1 5/16" OD Round Twist-lock Spreader Tip: SP-091TL: Improved Spreader Tip for 1 5/16" OD x 1 1/16" ID Spreader features a special 'twist-lock' design, and a smooth, broad end to minimize sail chafe. Shroud is secured without seizing wire, by inserting it horizontally into Spreader Tip and then 'twisting' it to lie in line with the mast. Tip accommodates shrouds up to 9/32" diameter and extends shroud seat 1/2" beyond spreader tube. Clear anodized aluminum Spreader Tip projects 1 1/16" (maximum) beyond spreader tube and is carefully rounded to reduce sail chafe.
|
|
|
Spreader Boot Pair for 1 5/16" OD Spreader: SP-057B: Spreader Boot for 1 5/16" OD Spreader is designed to reduce sail chafe. White Rubber Boot is attached to Spreader and Shroud using wire ties or Rigging Tape. Sold in Pairs only, they are (maximum) 5 3/4" long.
|
|
|
|
|
| Spreader Bases for 1 5/16" Round Spreaders | |
|
Spartan 1 5/16" Round Spreaders are normally used with Spreader Bases which are
formed to fit specific Mast Sections. Most Spreader Bases used with these Spreaders are
specific to individual Mast Sections and are listed under the Mast Sections that
they attach to, See Spartan Mast Sections.
Others are listed below. Some Spreader Bases are commonly used with Compression Tubes fitting over one or more mounting bolts, See Compression Tubes. |
|
|
Cast Spreader Base - Rectangular, Small: PP SBR-2027S: Rectangular Spreader Base for 1 5/16" OD Spreader. Anodized Cast Aluminum Spreader Base attaches to Mast with (2) 1/2" bolts on 3 11/16" (or 3 3/4") centers, lower bolt is also used to attach lower shroud Tang(s). Spreader is held in socket by 1/8" cotter Pin (included). Unit is 5 1/2" long x 2" wide, base is slightly contoured for use with a variety of Mast Sections. As used on Pearson 22, Ensign, Electra; Bristol 22, 24 and others. Unit also replaces old-style Male Spreader Base which was 5 1/4" x 2" with 1/2" holes on 3 3/8" centers. Note: Due to the variation in hole spacing, these units are supplied with only (1) bolt hole drilled, the second hole is drilled in the field; or can be drilled by us if measurements are supplied and time allows.
|
|
|
Cast Spreader Base - Rectangular, Large: PP SBR-2018L: Rectangular Spreader Base for 1 5/16" OD Spreader. Anodized Cast Aluminum Spreader Base attaches to Mast with (2) 1/2" bolts on 3 15/16" (or 4") centers, lower bolt is also used to attach lower shroud Tang(s). Spreader is held in socket by 1/8" cotter Pin (included). Unit is 6" long x 3" wide, base is slightly contoured for use with a variety of Mast Sections. As used on Pearson 26, Ariel, Commander, Renegade, Triton; and Bristol 26, 27, 29, 30, and others. Note: Due to the variation in hole spacing, these units are supplied with only (1) bolt hole drilled, the second hole is drilled in the field; or can be drilled by us if measurements are supplied and time allows.
|
|
|
|
|
|
1" Round Spreader Bar w/ Shroud Tang - C&C 24: CC SPBR-24: Aluminum Spreader Bar for 1 5/16" OD Spreader features integral slots for single Lower Shrouds using 3/16" AN (MS) Eyes. Round, anodized Spreader Bar is (maximum) 1" OD x 6 1/4" long, with 5/16" pin holes and is specially machined to allow a 5-degree vertical lift and accommodate lower shrouds. Designed for use with a 4" wide Mast. As used on C&C 24.
|
|
|
1" Round Spreader Bar w/ Shroud Tang - C&C 26: CC SPBR-26: Aluminum Spreader Bar for 1 5/16" OD Spreader features integral slots for single Lower Shrouds using 7/32" AN (MS) Eyes. Round, anodized Spreader Bar is (maximum) 1" OD x 6 3/4" long, with 5/16" pin holes and is specially machined to allow a 5-degree vertical lift and accommodate lower shrouds. Designed for use with a 4 1/2" wide Mast. As used on C&C 26. |
|
