 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
| Spinnaker Cars for Metric T-Track |
|
|
|
These Spinnaker Cars are designed to fit on Metric T-Track, which is thicker
than standard
US (imperial) T-Track, but is generally the same width. As a result, Cars for
Metric T-Track will fit standard US (imperial) T-Track of the same width, but Cars for
standard US (imperial) T-Track will Not fit Metric T-Track. If in doubt about which Track you
have,
you will have to measure the thickness of the Flange. Spinnaker Cars are held in place on the track either by a spring or screw pin, or by means of a line control system. Racing boats, large boats and those stowing their poles on the mast will generally use a line control system, for its ease and handling convenience. Spinnaker Cars are of two varieties: Ring Cars for standard Piston pole ends, and Toggle Cars for use with various Bell Ends. Please note that Ring Cars are not designed for, or recommended for vertical pole stowage applications. Spinnaker Cars are listed here by the Size of the Track that they fit on.
See also,
other Spinnaker Cars,
Spinnaker Poles & Parts,
and Track. |
|
|
| Spinnaker Cars for Metric T-Track |
|
|
||
| Spinnaker Cars for 26mm Metric T-Track | ||
Standard Metric 26mm T-Track is 26mm (>1") wide with a 4mm Flange (26x4mm), Standard US 1" T-Track is (25.4mm) wide with a 1/8" (3.2mm) Flange, they are Not compatible. Spinnaker Cars for 26mm Metric T-Track are listed below. For Cars designed to fit Standard US T-Track, See Spinnaker Cars for 1" T-Track. |
||
|
|
||
| Spinnaker Cars w/ Pin Stop for 26mm Metric T-Track | ||
| Spinnaker Toggle Car only, w/ Pin Stop: Har B-276B: Spinnaker Toggle Car only with Pin Stop for 26mm T-Track. Chrome-plated cast Bronze slide has plastic liners to minimize friction. Car is (maximum) 95mm (3 3/4") long x 42mm (1 5/8") wide, and accepts Toggle up to 1 1/2" (39mm) high using a 12mm vertical Pin. Includes plastic liners, Har B-276-LP. Spinnaker Car fits 1" and 26x4mm T-Track. Limited Availability.
|
 |
|
|
Replacement Liners for Spinnaker Car (pair): Har B-276-LP: Replacement Liners for Har B-276 Spinnaker Cars. Plastic liners are 98mm (3 7/8") long and are sold in pairs only. |
 |
|
|
|
||
| Spinnaker Cars w/ Towing Shackles for 26mm Metric T-Track | ||
Spinnaker Toggle Car only, w/ Tow Bails: Har B-276A: Spinnaker Toggle Car only with Towing Bails for 26mm T-Track. Chrome-plated cast Bronze slide has plastic liners to minimize friction. Car is (maximum) 135mm (5 3/8") long (with towing bails) x 42mm (1 5/8") wide, and accepts Toggle up to 1 1/2" (39mm) high using a 12mm vertical Pin. Includes plastic liners, Har B-276-LP. Spinnaker Car fits 1" and 26x4mm T-Track. Limited Availability.
|
 |
|
|
Replacement Liners for Spinnaker Car (pair): Har B-276-LP: Replacement Liners for Har B-276 Spinnaker Cars. Plastic liners are 98mm (3 7/8") long and are sold in pairs only. |
|
|
|
|
||
| Spinnaker Cars for 32mm Metric T-Track | ||
Standard Metric 32mm T-Track is 32mm (1 1/4") wide with a 5.5mm Flange (32x5.5mm), Standard US 1 1/4" T-Track is (32mm) wide with a 3/16" (5mm) Flange (32x5mm), they are Not compatible. Spinnaker Cars for 32mm Metric T-Track are listed below. For Cars designed to fit Standard US T-Track, See Spinnaker Cars for 1 1/4" T-Track. |
||
Spinnaker Ring Cars Spinnaker Toggle Cars w/ Pin Stop |
 32mm T-Track |
|
|
|
||
| Spinnaker Ring Cars w/ Pin Stop for 32mm T-Track | ||
|
Spinnaker Ring Car for 32mm T-Track: Sch 72-31X: Welded SS Spinnaker Ring Car for Standard 32mm T-Track. Formed SS Slide with SS Spring Pin is welded to 5/16" x 1 1/2" ID Ring. Slide is 4" long x 1 1/2" wide, and projects 2 1/2" (maximum) from Track surface.
|
 |
|
|
|
||
| Towable Spinnaker Ring Cars for 32mm T-Track | ||
|
Towable Spinnaker Ring Car for 32mm T-Track: NF 10688M: Heavy-duty Cast Spinnaker Car with rollers to fit Standard 32mm T-Track. Chrome plated Cast Bronze Car has 7/16" x 1 3/4" ID Ring with towing shackles, and features SS rollers against the top and sides of the track to insure free rolling under both side and compressive loads. Slide is 4 7/8" long (without shackles) x 2 5/16" wide, and projects 3" (maximum) from Track surface. Note: Car can only be positioned with control lines.
|
 |
|
|
|
||
| Spinnaker Toggle Cars w/ Pin Stop for 32mm Metric T-Track | ||
|
Spinnaker Toggle Car only, w/ Pin Stop: FM 32TC-P: Spinnaker Toggle Car only with Spring Pin stop for Standard 32mm T-Track. Chrome-plated cast Bronze slide has plastic liners to minimize friction, removable Spring Pin stop allows for later conversion to a Towing Car. Car is (maximum) 4 5/8" long x 1 13/16" wide, and accepts Toggle up to 1 1/2" (39mm) high using a 10mm vertical Pin. Includes plastic liners, FM 32TC-LP. Spinnaker Car fits 1 1/4" and 32x5.5mm T-Track. Note that this Car is commonly drilled for use with a 12mm vertical Pin, and is also available in that configuration, order FM 32TC-P-12.
|
 |
|
|
Replacement Liners for Spinnaker Car (pair): FM 32TC-LP: Replacement Liners for FM 32TC Spinnaker Cars. Plastic liners are 3 1/2" long and are sold in pairs only. LP-125M-90
|
 |
|
| Spinnaker Car w/ Metric Small Bell Fitting & Pin Stop: FM 32TC-P-MBS: | ||
|
Heavy-duty Spinnaker Car fits 1 1/4" and Standard 32mm T-Track. Unit includes
FM 32TC-P Car, above, and Small Barbarossa/ Harken Bell fitting, below.
Metric Small Bell Pole End Fittings, that the Bell works with, are commonly found
on tubes
of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. Please
note
that car must be mounted as pictured, with the Bell Trigger up otherwise Trigger will hit on Car
and end will release before pole is parallel to mast.
|
 |
|
|
Metric Small Bell & Toggle only: Har B-130: Replacement Metric Small Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Small Bell Pole Ends. Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD, Toggle has hole for 12mm vertical Pin and is 1 3/8" (34mm) high. Metric Small Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. See Spinnaker Poles & Parts.
|
 |
|
| Spinnaker Car w/ Metric Large Bell Fitting & Pin Stop: FM 32TC-P-MBL: | ||
|
Heavy-duty Spinnaker Car fits 1 1/4" and Standard 32mm T-Track. Unit includes
FM 32TC-P Car, above, and Large Francespar or Barbarossa/ Harken Bell
fitting, below,
which fit the same Pole Ends. Metric Large Bell Pole End Fittings, that the Bell
works with,
are commonly found on tubes of 70, 80 and 100mm OD, and extend approximately 4 3/8" (110mm)
beyond the
tube end. Please note that car must be mounted as pictured, with the Bell Trigger up otherwise
Trigger will
hit on Car and end will release before pole is parallel to mast.
|
||
|
Metric Large Bell & Toggle only: Har B-120: Replacement Metric Large Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Large Bell Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD, Toggle has hole for 12mm vertical Pin and is 1 3/8" (34mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. See Spinnaker Poles & Parts.
|
 |
|
|
Spinnaker Toggle Car only, w/ Pin Stop: Har B-348B: Spinnaker Toggle Car only with Spring Pin stop for 32mm T-Track. Chrome-plated cast Bronze slide has plastic liners to minimize friction. Car is 3 7/8" long x 1 13/16" wide, and accepts Toggle up to 1 1/2" (39mm) high using a 12mm vertical Pin. Includes plastic liners, Har B-348-LP. Spinnaker Car also fits the rare 32x6mm T-Track. Limited Availability.
|
 |
|
|
Replacement Liners for Spinnaker Car (pair): Har B-348-LP: Replacement Liners for Har B-348 Spinnaker Cars. Plastic liners are 3 7/8" long and are sold in pairs only.
|
 |
|
|
|
||
| Spinnaker Cars w/ Towing Shackles for 32mm Metric T-Track | ||
|
Spinnaker Toggle Car only, w/ Tow Shackles: FM 32TC-T: Spinnaker Toggle Car only with Towing Shackles for Standard 32mm T-Track. Chrome-plated cast Bronze slide has plastic liners to minimize friction. Car is (maximum) 4 5/8" long (without shackles) x 1 13/16" wide, and accepts Toggle up to 1 1/2" (39mm) high using a 10mm vertical Pin. Includes plastic liners, FM 32TC-LP. Spinnaker Car fits 1 1/4" and 32x5.5mm T-Track. Note that this Car is commonly drilled for use with a 12mm vertical Pin, and is also available in that configuration, order FM 32TC-T-12.
|
 |
|
|
Replacement Liners for Spinnaker Car (pair): FM 32TC-LP: Replacement Liners for FM 32TCC Spinnaker Cars. Plastic liners are 3 1/2" long and are sold in pairs only. LP-125M-90
|
 |
|
| Spinnaker Car w/ Metric Small Bell Fitting & Tow Shackles: FM 32TC-T-MBS: | ||
|
Heavy-duty Spinnaker Car fits 1 1/4" and Standard 32mm T-Track, and incorporates a
Small Barbarossa/ Harken Bell fitting with Toggle. Chrome-plated cast Bronze slide has
plastic liners to minimize friction. Car includes Small Barbarossa (Harken) Bell fitting,
Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD. Slide is
(maximum) 4 5/8"
long (without shackles) x 1 3/4" wide.
Metric Small Bell Pole End Fittings, that the Bell works with, are commonly found on
tubes
of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. Please
note
that car must be mounted as pictured, with the Bell Trigger up otherwise Trigger will hit on Car
and end will release before pole is parallel to mast.
|
||
|
Metric Small Bell & Toggle only: Har B-130: Replacement Metric Small Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Small Bell Pole Ends. Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD, Toggle has hole for 12mm vertical Pin and is 1 3/8" (34mm) high. Metric Small Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. See Spinnaker Poles & Parts.
|
 |
|
| Spinnaker Car w/ Metric Large Bell Fitting & Tow Shackles: FM 32TC-T-MBL: | ||
|
Heavy-duty Spinnaker Car fits 1 1/4" and Standard 32mm T-Track, and incorporates a
Large
Francespar or Barbarossa Bell fitting with Toggle. Chrome-plated cast Bronze slide has plastic
liners to minimize friction. Car includes Large Francespar or Barbarossa (Harken) Bell fitting,
which fit the same Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately
3 1/4" (82mm) OD.
Slide is (maximum) 4 5/8" long (without shackles) x 1 3/4" wide, replacement Liners, below, are
also available.
Metric Large Bell Pole End Fittings, that the Bell works with, are commonly found on
tubes of
70, 80 and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end.
Please note that car must be mounted as pictured, with the Bell Trigger up otherwise Trigger
will hit on Car
and end will release before pole is parallel to mast.
|
 |
|
|
Francespar Large Bell & Toggle only: FSP B-120SC: Francespar Large Bell & Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Large Bell Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD, Toggle has hole for 10mm vertical Pin and is 1 1/2" (37mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. As used with Isomat NGA-51-BL, and other Spinnaker Cars.
|
||
|
Metric Large Bell & Toggle only: Har B-120: Replacement Metric Large Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Large Bell Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD, Toggle has hole for 12mm vertical Pin and is 1 3/8" (34mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. See Spinnaker Poles & Parts.
|
|
|
|
|
||
| Spinnaker Track Ends for 32mm Metric T-Track | ||
|
Spinnaker Track End, w/ Sheave: FM 32T-CE: Spinnaker Track End with Sheave for Standard 32mm T-Track is used with Towing Cars. Cast SS Control End has 35mm turned Delrin Sheave for up to 3/8" (10mm) line. Unit is (maximum) 75mm (3") long x 38mm (1 1/2") wide, and is attached with (2) 6mm RH screws on 45mm centers, with one screw going through an 11mm Stop hole in the Track. Unit is marked 33513000054.
|
||
|
Spinnaker Track End Stop: FM 32T-ES: Black plastic Track End for Standard 32mm T-Track. Molded Track End is (maximum) 36mm long x 32mm wide and is attached to Mast with an 8mm (5/16") FH screw. |
||